Muhammad Aizi Mat Salim

Muhammad Aizi Mat Salim

Auto-generated profile, based on publicly available information

Muhammad Aizi Mat Salim

Photonics Research Centre, University of Malaya, 50603 Kuala Lumpur, Malaysia

Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
19 July 2016 in Laser Physics Letters
Verified
Journal Article
Closed access
PDF file
FRF A A Rashid
F A A Rashid
SASaaidal Razalli Azzuhri
Saaidal Razalli Azzuhri
MSM A M Salim
M A M Salim
RSR A Shaharuddin
R A Shaharuddin
MIM A Ismail
M A Ismail
HAHarith Ahmad
Harith Ahmad
Using a few-layer black phosphorus (BP) thin film that acts as a saturable absorber (SA) in an ytterbium-doped fiber laser setup, we experimentally demonstrated a passively dual-wavelength Q-switching laser operation. The setup also incorporated a D-shaped polished fiber as a wavelength selective filter. As the SA was used in the ring cavity, a dual-wavelength Q-switch produced consistent outputs at 1038.68 and 1042.05 nm. A maximum pulse energy of 2.09 nJ with a shortest pulse width of 1.16 µs was measured for the achieved pulses. In addition, the repetition rate increased from 52.52 to 58.73 kHz with the increment of the pump level. Throughout the measurement process, the results were obtained consistently and this demonstrates that the BP film is a very good candidate to produce Q-switching pulses for the 1 micron region.

21 August 2020 in IEEE Transactions on Instrumentation and Measurement
Verified
Journal Article
Closed access
KLKok-Sing Lim
Kok-Sing Lim
MZMuhammad Khairol Annuar Zaini
Muhammad Khairol Annuar Zaini
ZOZhi Chao Ong
Zhi Chao Ong
FAFairul Zahri Mohamad Abas
Fairul Zahri Mohamad Abas
MSMuhammad Aizi Bin Mat Salim
Muhammad Aizi Bin Mat Salim
HAHarith Ahmad
Harith Ahmad
In this article, we present a vibration measurement system based on low-frequency cantilever-based fiber Bragg grating accelerometers (CFAs) for a suspension bridge. Each accelerometer has an end-loaded cantilever beam, specifically tailored to achieve a uniform sensitivity for a frequency range of 0-4 Hz, a suitable detection range for the vibration analysis. In the field test, seven CFAs were installed at specific positions along the deck of a 110-m-long suspension bridge for synchronous multipoint vibration measurements. The reflection spectra of the CFA array were recorded and processed using the pseudo-high-resolution scheme to improve the signal quality and measurement accuracy. Three natural vibration frequencies: 1.15, 1.54, and 3.17 Hz have been identified from the measurement. Following that, the acquired time-domain signals were processed by a digital bandpass filter to retrieve the waveform at each natural frequency to determine the corresponding mode shapes. The results are in agreement with the phase difference between the frequency domain signal for each natural frequency. This investigation has shown the feasibility of the proposed measurement system for determining the mode shapes and dynamic frequency analysis of a suspension bridge. It is a potential method for structural health monitoring for other similar civil structures.

19 August 2016 in Laser Physics Letters
Verified
Journal Article
Closed access
PDF file
HAHarith Ahmad
Harith Ahmad
MSM A M Salim
M A M Salim
KTK Thambiratnam
K Thambiratnam
SNS F Norizan
S F Norizan
SHS W Harun
S W Harun
A compact, passively Q-switched fiber laser with a tunable output is demonstrated. The proposed system uses a short length ytterbium doped fiber to create a very stable and compact optical circuit that uses black phosphorus (BP) as a saturable absorber to generate the desired short pulses. A stable Q-switch pulse train is obtained, with an operational wavelength range from 1056.6–1083.3 nm. Concurrently, a maximum pulse energy and minimum pulse width as well as a repetition rate range of 7.1 nJ, 4 µ s and 6.0–44.8 kHz respectively was obtained. The proposed system will be able to cater to a multitude of applications that require a compact yet robust and cost-effective pulse laser.

18 March 2016 in Applied Physics B
Verified
Journal Article
Closed access
PDF file
HAHarith Ahmad
Harith Ahmad
Zian Cheak TiuZian Cheak Tiu
Zian Cheak Tiu
AZArman Zarei
Arman Zarei
MSMuneswaran Suthaskumar
Muneswaran Suthaskumar
MSMuhammad Aizi Mat Salim
Muhammad Aizi Mat Salim
SHSulaiman Wadi Harun
Sulaiman Wadi Harun

1 June 2018 in Results in Physics
Verified
Journal Article
Open access
SAS.R. Azzuhri
S.R. Azzuhri
IAI.S. Amiri
I.S. Amiri
AZA.S. Zulkhairi
A.S. Zulkhairi
MSM.A.M. Salim
M.A.M. Salim
MRMohd Zulhakimi Ab Razak
Mohd Zulhakimi Ab Razak
PYP. Yupapin
P. Yupapin

20 October 2016 in Laser Physics
Verified
Journal Article
Closed access
PDF file
HAHarith Ahmad
Harith Ahmad
MSM A M Salim
M A M Salim
MIM F Ismail
M F Ismail
SHS W Harun
S W Harun
A Q-switched ytterbium doped fiber laser (YDFL) with a ZnO saturable absorber (SA) is used to demonstrate the generation of pulses in the 1 micron region. The system has a Q-switching threshold of approximately 115.2 mW, and can generate pulses with a 3.0 µ s full-width at half maximum as well as a peak-to-pedestal ratio of 53.0 dB. No spectral modulations are observed, indicating a highly stable system. The pulse output of the proposed system has repetition rates and pulse widths of approximately 50 kHz and 1.6 µ s, as well as an average output power of 0.14 mW and a pulse energy of 2.8 nJ at its highest pump power of 196 mW. This is the first time, to the authors’ knowledge, that a ZnO based SA has been used to generate pulses in the 1 micron region with a YDFL.