Molybdenum disulfide (MoS2) is a promising candidate for the development of high-performance photodetectors, due to its excellent electric and optoelectronic properties. However, most of the reported MoS2 phototransistors have adopted a back-gate field-effect transistor (FET) structure, requiring applied gate bias voltages as high as 70 V, which made it impossible to modulate each detecting device in the fabricated array. In this paper, buried-gate FETs based on CVD-grown monolayer MoS2 were fabricated and their electric and photoelectric properties were also systematically investigated. A photoresponsivity of around 6.86 A/W was obtained at 395 nm, under the conditions of zero gate bias voltage and a light power intensity of 2.57 mW/cm2. By application of a buried-gate voltage of 8 V, the photoresponsivity increased by nearly 10 times. Furthermore, the response speed of the buried-gate MoS2 FET phototransistors is measured to be around 350 ms. These results pave the way for MoS2 photodetectors in practical applications.
The high-temperature pressure sensors have wide applications in aerospace, petroleum, geothermal exploration, automotive electronics and other fields. However, the traditional silicon pressure sensors are restricted to pressure measurement under 120 °C and cannot be satisfied to measure the pressure of various gases or liquids in high temperature and other harsh environments. This paper proposes a novel high temperature pressure sensor based on graphene, in which a rectangular cavity is applied to improve the piezoresistive characteristics of the sensor. The unique of this sensor is that the graphene is coated by the silicon nitride (Si 3 N 4 ) membrane, which could avoid the oxidation of graphene in high-temperature and increase the temperature tolerance range. The sensor was placed at various temperatures (50-420 °C) to explore the temperature characteristics, achieving a maximal temperature coefficient of resistance (TCR) of 0.322% °C -1 . Moreover, the sensor with a 64×9 μm 2 cavity has a high pressure sensitivity of 5.32×10 -4 kPa -1 , enabling a wide range from 100 kPa to 10 Pa. Experimental results indicate that the proposed sensor possesses superior pressure sensitivity, a wide pressure detection range and high-temperature tolerance of 420 °C, which provides new insight into fabricating high-temperature pressure sensors based on graphene and creates more applications in different fields.
The flexible pressure sensors enable their extensive utilization across a wide range of domains, encompassing wearable electronic devices, human-machine interface, electronic skin, and intelligent medical treatment. In recent years, the rapid advancements in technologies such as the Internet of things and artificial intelligence, coupled with growing functional requirements, have given rise to a flourishing research domain focused on high-performance flexible pressure sensors. Theoretical models, structural design, and process preparation have continuously advanced flexible pressure sensors based on traditional materials. However, these advancements still fall short of meeting the demand for high quality, high sensitivity, and extensive measurement capabilities. Meanwhile, the excellent mechanical and electrical properties of two-dimensional (2D) materials make them the best candidate material for the next generation of pressure sensors. However, the advancement of flexible pressure sensors is currently constrained by factors such as the challenge posed by mechanical crosstalk in extensive arrays, the impact of environmental variables on achieving optimal performance, and the intricate task of decoupling multiple signals. This paper reviews the current status and applications of flexible pressure sensors in recent years. And puts forward some current challenges, which provides a valuable guide for future developments in this field. This review shed light on the future of flexible pressure sensors.
Being an excellent representative of atomically thin 2-D materials, graphene has attracted extensive research attention in the fields of electronic and optoelectronic devices. However, its low-light absorption coefficient, gapless nature, and short carrier lifetime hinder its development in photodetectors. Another atomically thin 2-D semiconducting material molybdenum disulfide (MoS2) has stronger light interaction. Here, we show a high-performance photodetector based on graphene/MoS2 heterojunction field effect transistors (FETs), where the electrodes are fabricated in the middle of two materials. Graphene functions as a conductive material that improves the carrier transmit speed of the device. Meanwhile, MoS2 mainly functions as a light-sensitive material that promotes the generation of photogenerated carriers. The combination of the two materials substantially improves the performance of the photodetector. The photoresponsivity of our device was demonstrated up to ${1.5} \times {10} ^{{4}}$ A/W under a 470-nm light-emitting diode (LED) light illumination, which was much higher than that of a reported photodetector based on monolayer graphene or MoS2 (~mA/W). Moreover, the photoresponsivity of the device could be easily tuned by applying buried-gate, back-gate, and source–drain voltage, which has important implications for the application of 2-D material photodetectors in neural network image sensor arrays. Our study established a method for large-scale preparation of high-performance photodetector arrays based on 2-D materials heterojunctions.
In this paper, a three-dimensional (3D) photodetector based on a single wall carbon nanotube (SWCNT) and graphene heterojunction has been fabricated by a self-rolled-up process. In the designed structure, graphene acted as the conductive channel and SWCNTs absorbed the incident light ranging from the visible to near-infrared bands. Compared to planar (two-dimensional, 2D) devices, 3D microcavities provided a natural resonant cavity to enhance the optical field, which improved the photoresponsivity. This 3D heterojunction photodetector realized a broadband photodetection from 470 to 940 nm with an ultrahigh photoresponsivity of 4.9 × 104 A W−1 (@ 590 nm) and 1.9 × 104 A W−1 (@ 940 nm), a fast photoresponse speed of 1.6 ms, and an excellent sensitivity of 2.28 × 1011 Jones. Besides, the fabricated photodetector showed favorable mid-infrared detection with a photoresponsivity of 3.08 A W−1 at 10.6 μm. Moreover, the photodetector exhibited a promising room-temperature imaging capability. The 3D heterojunction photodetector would provide a feasible pathway to realize graphene-based photodetectors with high performance and could be extended to be integrated with other light absorptive materials.
Temperature sensor is one of the primarily developed and most proverbially utilized sensors. Owing to the limitations of their characteristics (stability, thermal conductivity, and thermal contact area), traditional temperature sensors may exhibit drawbacks of high production cost and large volume. In this paper, a three-dimensional (3D) buried-gate graphene field effect transistors (GFETs) are proposed as a novel sensor for temperature detection, which possess a 3D microtube structure by self-rolled-up technology. Compared to conventional two-dimensional (2D) devices, the 3D devices would have tinier area and higher integration. Two main reasons that would affect the resistance of the graphene are the graphene electro-phonon coupling and the thermal expansion effect. In addition, by applying the COMSOL Multiphysics software, it has been demonstrated that the microtube would deform to a certain extent when the temperature increases. And the strain on the 3D devices is proved to be greater than that of the 2D devices. Experimental results show that 3D GFETs could realize temperature detection between 30 °C and 150 °C, and its resistance increases with temperature rising. Furthermore, the maximum achieved temperature coefficient of resistance (TCR) is 0.41% °C −1 and the hysteresis error is only 3.85%. By virtue of the 3D microtube, not only more superior temperature detection could be achieved, but also more devices are integrated in unit area. The 3D temperature sensor possesses superior sensitivity, repeatability and stability, which contributes a new approach to develop the high-performance temperature sensor.