Molybdenum disulfide (MoS2) is a promising candidate for the development of high-performance photodetectors, due to its excellent electric and optoelectronic properties. However, most of the reported MoS2 phototransistors have adopted a back-gate field-effect transistor (FET) structure, requiring applied gate bias voltages as high as 70 V, which made it impossible to modulate each detecting device in the fabricated array. In this paper, buried-gate FETs based on CVD-grown monolayer MoS2 were fabricated and their electric and photoelectric properties were also systematically investigated. A photoresponsivity of around 6.86 A/W was obtained at 395 nm, under the conditions of zero gate bias voltage and a light power intensity of 2.57 mW/cm2. By application of a buried-gate voltage of 8 V, the photoresponsivity increased by nearly 10 times. Furthermore, the response speed of the buried-gate MoS2 FET phototransistors is measured to be around 350 ms. These results pave the way for MoS2 photodetectors in practical applications.
24 May 2024 in IEEE Transactions on Terahertz Science and Technology
The manufacturing of three-dimensional (3D) metamaterials remains a major challenge and the narrow-band absorption characteristics limit the practical applications of terahertz metamaterial absorbers. To this end, we propose to combine the 3D printing technology with the microfluidics technique to fabricate a terahertz (THz) metamaterial absorber with a relative broad band (∼0.3 THz) under 1 THz. Here, the absorber consists of embedded multilayer disk microfluidics channels stacked vertically within the resin and filled with liquid metal (LM). It has been demonstrated that the experimental results agree well with the simulations, where the absorber exhibits polarization sensitive and incident angle insensitive in the frequency range from 0.25 to 0.6 THz. The proposed method enables the fabrication of terahertz metamaterial devices with complex structures in a fast, simple and low-cost way, which is no longer limited to conventional photolithography processes. This approach effectively stimulates many potential applications in emerging THz technologies, such as sensing, imaging, and wireless communications.
The progressive reduction in feature size presents significant challenges such as crosstalk, heat dissipation, and high-power consumption, which impede the advancement of Moore's Law. To overcome the limitations of silicon materials, it is crucial to identify subsequent iterations of innovative semiconductor materials or alternative structures. The integration of two-dimensional (2D) materials and three-dimensional (3D) structures offers a promising platform for exploring novel photodetectors and alternative pathways toward “More than Moore” technologies. In this study, we present a comprehensive evaluation of the underlying mechanisms governing the formation of diverse 3D structures, along with their corresponding preparation methodologies. We focus our evaluation on the distinctive optical properties arising from the incorporation of a self-rolled-up 3D structure into 2D materials and heterojunctions photodetector. Finally, we address some of the challenges and outlook that persist in the development and application of 3D-structured photodetectors based on 2D materials.
Three-dimensional vertical resistive random access memory (VRRAM) is proposed as a promising candidate for increasing resistive memory storage density, but the performance evaluation mechanism of 3-D VRRAM arrays is still not mature enough. The previous approach to evaluating the performance of 3-D VRRAM was based on the write and read margin. However, the leakage current (LC) of the 3-D VRRAM array is a concern as well. Excess leakage currents not only reduce the read/write tolerance and liability of the memory cell but also increase the power consumption of the entire array. In this article, a 3-D circuit HSPICE simulation is used to analyze the impact of the array size and operation voltage on the leakage current in the 3-D VRRAM architecture. The simulation results show that rapidly increasing leakage currents significantly affect the size of 3-D layers. A high read voltage is profitable for enhancing the read margin. However, the leakage current also increases. Alleviating this conflict requires a trade-off when setting the input voltage. A method to improve the array read/write efficiency is proposed by analyzing the influence of the multi-bit operations on the overall leakage current. Finally, this paper explores different methods to reduce the leakage current in the 3-D VRRAM array. The leakage current model proposed in this paper provides an efficient performance prediction solution for the initial design of 3-D VRRAM arrays.
31 August 2011 in The Journal of China Universities of Posts and Telecommunications