26 December 2024 in IEEE Transactions on Components, Packaging and Manufacturing Technology
The amorphous wire demonstrate good soft magnetic properties and the giant magnetoimpedance effect (GMI). However, the amorphous wire with diameter ranging from several micrometers to several tens of micrometers is soft and thin, thus it is difficult to handle and fabricate to achieve a magnetic sensor. In addition, the electrical contact resistance of the amorphous wire with pads shows wide distribution due to the contact area is hard to control when welding. To solve these problems, this paper proposed a microelectronic fabrication method for amorphous wire based magnetic sensor. Glass wafer was used as the supporting substrate of the amorphous wire, and nonphotosensitive polyimide resin was employed as the electroplating mask. Electroplating was performed to achieve the electrical interconnection between the amorphous wire and pads on the substrate. The structure fabricated above was composed of amorphous wire and supporting glass substrate. Then, enamelled wire was uniformly wound around the fabricated structure as signal pickup coil. The test results showed excellent linearity within the range of -0.6 Oe to +0.6 Oe, and sensitivity of 6.38 V/Oe.
15 July 2025 in IEEE Transactions on Magnetics
Amorphous wires show the advantages of high permeability, low coercivity, and low hysteresis loss; therefore, they are suitable as magnetic cores for fluxgate magnetometers. In residence times difference (RTDs) fluxgate magnetometers, the application of amorphous wires as magnetic cores has primarily focused on the use of a single wire. To achieve higher precision in weak magnetic field detection, further improvement in resolution is required. In this article, we designed a multicore RTD fluxgate magnetometer based on composite amorphous wire arrays. We tested RTD fluxgate magnetometers with different numbers of amorphous wires (one, two, three, and six wires) as the magnetic cores. The test results showed that as the number of amorphous wires in the magnetic core increased, the resolution of the RTD fluxgate magnetometer improved from 5.15 to 0.17 nT, demonstrating that increasing the number of wires in the magnetic core effectively enhanced the resolution of the RTD fluxgate magnetometer.
23 September 2025 in IEEE Electron Device Letters
Amorphous wires, with high permeability, near-zero magnetostriction, and excellent sensitivity, have shown significant advantages in weak magnetic sensor applications. However, the mass production of amorphous wire based magnetic sensor presents challenges due to the filamentary morphology of the material, which makes it difficult to handle and not compatible to microfabrication processes. Here, we report a method for manipulating filament like material to achieve wafer-level fabrication of amorphous wire sensors. Amorphous wires are accurately aligned and placed into the microgrooves formed by polyimide and temporarily fixed by using a permanent magnet. Then copper micro-coil is fabricated by photolithography and electroplating, which is wrapped around the amorphous wire. The proposed method is compatible with standard Micro-Electro-Mechanical System (MEMS) process and does not need special equipment to manipulate amorphous wires. The average lateral offset of the amorphous wires from the groove centers in the randomly selected devices is less than 30 μm, demonstrating the feasibility of the proposed method. This work provides a wafer-level manufacturing process for amorphous wire based Giant Magneto-Impedance (GMI) sensors.
27 October 2025 in IEEE Transactions on Magnetics
Giant magnetoimpedance (GMI) sensors with off-diagonal mode have advantages of wide range, good linearity and simple circuit. The performance of the sensor is directly affected by the number of turns of the signal pickup coil. In order to obtain amorphous wire GMI sensors with better performance, the number of turns of the signal pickup coil is usually larger. However, large pickup coils result in larger device size, which is not convenient to device miniaturization. In many conditions, small size device is needed. To achieve device miniaturization and keep the performance at the same time, increasing the cross-sectional area of the sensor is another choice. This paper investigates the GMI sensor performance with varying amorphous wires. The aim is to provide a viable approach to enhance the sensor performance with miniaturized device size. We investigate the influence of the number of amorphous wires and coil turns on the performance of amorphous wire based GMI sensors. The off-diagonal output responses of sensor with different numbers of wires were measured, and the output sensitivity and noise were compared for varying numbers of amorphous wires. The sensitivity of the sensor with a single amorphous wire is 85.23 mV/Oe, while that with eight amorphous wires reaches 266.36 mV/Oe. The noise level of the sensor with a single amorphous wire is 148.4 pT/rtHz@1 Hz, and the eight amorphous wires is 44.5 pT/rtHz@1 Hz. This work presents an approach to achieve a high performance GMI sensor with less number of pickup coils.
22 April 2026 in IEEE Transactions on Components, Packaging and Manufacturing Technology
Amorphous wire giant magnetoimpedance (GMI) sensors exhibit advantages such as high sensitivity, fast response, and compact size. To achieve scalable manufacturing, microelectronic manufacturing has been adopted to ensure device consistency and enable mass production. However, challenges remain in the packaging stage. The research on the packaging approaches specifically for this type of sensor is insufficient. Traditional packaging approaches, such as ceramic packaging methods and lead-frame packaging methods, face issues including high cost and large dimensions. Compared to traditional packaging, the chip-on-board (COB) packaging provides the advantages of compact size and low cost. To address the problem in the sensor packaging stage, this paper proposes a COB packaging scheme for amorphous wire sensors and has achieved device fabrication. The sensor based on microelectronic manufacturing technology is attached to the printed circuit board (PCB). Electrical connection of the amorphous wire is achieved by wire bonding, and the gold wires are used to connect the pads at both ends of the amorphous wire to the corresponding pads on the PCB. Finally, the epoxy encapsulant is employed on the chip and bonding wire areas, fully covering both to complete the COB packaging of the device. The amorphous wire weak magnetic sensor after COB packaging exhibits excellent linearity within a magnetic field range of –0.75 Oe to +0.75 Oe, with a sensitivity of 5.19 V/Oe and a noise level of 94 pT/√Hz at 1 Hz (21 pT/√Hz at 1 kHz).
10 November 2026 in Sensors and Actuators A: Physical