Agrim Gupta

Agrim Gupta

Auto-generated profile, based on publicly available information

Agrim Gupta

University of California San Diego, La Jolla, USA

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
26 March 2021 in IEEE Transactions on Communications
Verified
Journal Article
Closed access
SNSarthak Nijhawan
Sarthak Nijhawan
AGAgrim Gupta
Agrim Gupta
KAKumar Appaiah
Kumar Appaiah
RVRahul Vaze
Rahul Vaze
NKNikhil Karamchandani
Nikhil Karamchandani
The use of channel state information (CSI) at the transmitter significantly enhances the performance of wireless communication systems. However, the requirement of CSI feedback places an undue burden on the reverse link, especially in links that employ multiple-input multiple-output (MIMO) and orthogonal frequency division multiplexing (OFDM), where CSI takes the form of a precoding matrix (precoder) for each subcarrier. Typical deployments use quantization and feedback of CSI at certain subcarriers, with interpolation to fill in missing CSI at the transmitter. Past work has used the orthogonal structure of precoders with Flag manifolds for quantization and interpolation of CSI, although interpolation is complicated due to the absence of analytic expressions for geodesics on Flag manifolds. Other approaches have involved the parameterization of the precoder into scalar parameters that are amenable to quantization and interpolation. In this paper, we present efficient methods to quantize and interpolate on Flag manifolds, using both optimal algorithms as well as simplified suboptimal algorithms. Further, we unify these with the parameterization based approaches and show that these translate directly to low-complexity quantization and interpolation on Flag manifolds. Simulations reveal that the proposed precoder quantization and interpolation effectively enhance achievable rates with limited complexity.

4 December 2024
Verified
Conference Paper
Open access
AGAgrim Gupta
Agrim Gupta
AHAdel Heidari
Adel Heidari
AKAvyakta Kalipattapu
Avyakta Kalipattapu
IJIsh Jain
Ish Jain
DBDinesh Bharadia
Dinesh Bharadia
With 6.5 billion smartphones in use worldwide, each relying on a battery for key subsystems like display, compute, and cellular connectivity, previous studies on power consumption often used invalidated indirect estimates that failed to isolate specific hardware usage. We address this by utilizing Google's On Device Power Rails Monitor (ODPM) tool for precise power measurements of individual components. Our findings indicate that connectivity (Wi-Fi, 4G/5G) and screen display are the primary power consumers, as shown with the Google Pixel 7A. We also confirmed similar power consumption trends using an energy estimation method on the Samsung S23+. Given the prevalence of smartphones, we discuss the challenges and opportunities for optimizing power usage.

27 March 2023 in Proceedings of the ACM on Interactive, Mobile, Wearable and Ubiquitous Technologies
Verified
Journal Article
Open access
AGAgrim Gupta
Agrim Gupta
DPDaegue Park
Daegue Park
SBShayaun Bashar
Shayaun Bashar
CGCedric Girerd
Cedric Girerd
NBNagarjun Bhat
Nagarjun Bhat
DBDinesh Bharadia
Dinesh Bharadia
Any two objects in contact with each other exert a force that could be simply due to gravity or mechanical contact, such as any ubiquitous object exerting weight on a platform or the contact between two bones at our knee joints. The most ideal way of capturing these contact forces is to have a flexible force sensor which can conform well to the contact surface. Further, the sensor should be thin enough to not affect the contact physics between the two objects. In this paper, we showcase the design of such thin, flexible sticker-like force sensors dubbed as 'ForceStickers', ushering into a new era of miniaturized force sensors. ForceSticker achieves this miniaturization by creating new class of capacitive force sensors which avoid both batteries, as well as wires. The wireless and batteryless readout is enabled via hybrid analog-digital backscatter, by piggybacking analog sensor data onto a digitally identified RFID link. Hence, ForceSticker finds natural applications in space and battery-constraint in-vivo usecases, like force-sensor backed orthopaedic implants, surgical robots. Further, ForceSticker finds applications in ubiquiti-constraint scenarios. For example, these force-stickers enable cheap, digitally readable barcodes that can provide weight information, with possible usecases in warehouse integrity checks. To meet these varied application scenarios, we showcase the general framework behind design of ForceSticker. With ForceSticker framework, we design 4mm*2mm sensor prototypes, with two different polymer layers of ecoflex and neoprene rubber, having force ranges of 0-6N and 0-40N respectively, with readout errors of 0.25, 1.6 N error each (10,000 force applications without significant error degradation. We also showcase two case-studies onto the possible applications of ForceSticker: sensing forces from a toy knee-joint model and integrity checks of warehouse packaging.

4 November 2024
Verified
Conference Paper
Open access
NBNagarjun Bhat
Nagarjun Bhat
AGAgrim Gupta
Agrim Gupta
IBIshan Bansal
Ishan Bansal
HGHarine Govindarajan
Harine Govindarajan
DBDinesh Bharadia
Dinesh Bharadia
Sensors enable us to digitally capture stimuli like moisture, light, and force. Despite their low cost, reliability, and scalability, the lack of widespread adoption of IoT has hindered the realization of true ubiquitous sensing. A likely reason is that the current sensor platforms are bulky due to the batteries and complex electronics needed to interface sensors communication systems. In this work, we present a fully-passive, miniaturized, flexible form factor sensor interface titled ZenseTag that uses minimal electronics to read and communicate analog sensor data, directly at radio frequencies (RF). We exploit the fundamental principle of resonance, where a sensor's terminal impedance becomes most sensitive to the measured stimulus at its resonant frequency. This enables ZenseTag to read out the sensor variation using only energy harvested from wireless signals. We demonstrate its implementation with a 15x10mm flexible PCB that connects sensors to a printed antenna and passive RFID ICs, enabling near real-time readout through a performant GUI-enabled software. We showcase ZenseTag's versatility by interfacing commercial force, soil moisture and photodiode sensors [1--3]. Further, we motivate dedicated application studies for these sensors.

14 October 2022 in IEEE Transactions on Wireless Communications
Verified
Journal Article
Closed access
SNSajjad Nassirpour
Sajjad Nassirpour
AGAgrim Gupta
Agrim Gupta
AVAlireza Vahid
Alireza Vahid
DBDinesh Bharadia
Dinesh Bharadia
Digital and analog beamforming are well-known methods to suppress interference using multiple-antenna structures, but they have practical limitations: (i) Digital beamforming requires multiple analog-to-digital converters (ADCs) to enable digital conversion, which increases the cost and complexity; (ii) Although analog beamforming does not require expensive ADCs, it uses phase shifters, which cause quantization errors, insertion losses, and reduced power efficiency. In this paper, we consider a K -user uplink interference channel and propose a low-complexity algorithmic interference-suppression solution relying on simple switch-based reconfigurable antennas at the receivers. We utilize switches to enable/disable antennas to maximize each user’s signal-to-interference-plus-noise ratio (SINR). We present an optimization approach to approximate the optimal solution. To evaluate the results, we compare our method with relevant benchmarks. Moreover, we derive a lower bound on the minimum number of antenna elements per receiver to attain the desired SINR and verify the findings via simulations.

2 October 2023
Verified
Conference Paper
Open access
AGAgrim Gupta
Agrim Gupta
SNSajjad Nassirpour
Sajjad Nassirpour
MDManideep Dunna
Manideep Dunna
EPEamon Patamasing
Eamon Patamasing
AVAlireza Vahid
Alireza Vahid
DBDinesh Bharadia
Dinesh Bharadia
With the turn of new decade, wireless communications face a major challenge on connecting many more new users and devices, at the same time being energy efficient and minimizing its carbon footprint. However, the current approaches to address the growing number of users and spectrum demands, like Massive MIMO, demand exorbitant energy consumption. The reason is that traditionally Massive MIMO requires a digital beamforming architecture that needs a separate RF chain per antenna, so the power consumption scales with number of antennas. Instead, GreenMO creates a new Massive MIMO architecture with just a single physically laid RF chain, shared by all the antennas and introduces for the first time, the concept of virtualizing the RF chain hardware. That is, GreenMO creates an optimal number of virtual RF chains to serve a given number of spatial streams, depending on channel conditions and network load. Due to efficient, softwarized control over the number of virtual RF chains, GreenMO paves the way for green and flexible massive MIMO. We prototype GreenMO on a PCB with eight antennas and evaluate it with a WARPv3 SDR platform in an office environment. The results demonstrate that GreenMO is 3× more power-efficient than traditional Massive MIMO and 4× more spectrum-efficient than traditional OFDMA systems, while multiplexing 4 spatial streams, and can save upto 50% power in modern 5G NR base stations.