1 September 2016 in Acta Materialia
10 February 2019 in Advanced Functional Materials
The doping of semiconductor materials is a fundamental part of modern technology, but the classical approaches have in many cases reached their limits both in regard to achievable charge carrier density as well as mobility. Modulation doping, a mechanism that exploits the energy band alignment at an interface between two materials to induce free charge carriers in one of them, is shown to circumvent the mobility restriction. Due to an alignment of doping limits by intrinsic defects, however, the carrier density limit cannot be lifted using this approach. Here, a novel doping strategy using defects in a wide bandgap material to dope the surface of a second semiconductor layer of dissimilar nature is presented. It is shown that by depositing an insulator on a semiconductor material, the conductivity of the layer stack can be increased by 7 orders of magnitude, without the necessity of high‐temperature processes or epitaxial growth. This approach has the potential to circumvent limits to both carrier mobility and density, opening up new possibilities in semiconductor device fabrication, particularly for the emerging field of oxide thin film electronics.
4 May 2021 in Journal of Applied Physics
The correlation between defect chemistry, leakage currents, and time-dependent dielectric breakdown was studied for PbZr0.52Ti0.48O3 (PZT) films doped with 0.5, 1, 2, or 4 mol. % Nb. As the samples are nearly intrinsic (that is, close to n- to p-type transition), signatures for both hole hopping between Pb2+ and Pb3+ and electron trapping by Ti4+ were observed. For all doping levels, the dominant conduction mechanism transitioned from Poole–Frenkel emission at lower electric fields to Schottky emission at higher electric fields. The electric field for this transition diminishes from 172 to 82 kV/cm with decreasing Nb concentration. The concomitant modification of the Schottky barrier height from 1.24 to 0.95 eV with decreasing Nb concentration is attributed to Fermi level pinning via oxygen vacancies. The DC resistance degradation was controlled by Schottky emission from 250 to 400 kV/cm. It was found that the lifetime of the films increases with increasing the Nb level. The effective Schottky barrier height for 2 mol. % Nb-doped PZT films decreased from 1.12 to 0.85 eV during degradation. This is related to the movement of oxygen vacancies toward the cathode and the observation of Ti3+ near the cathode, which are proved via thermally stimulated depolarization current and electron energy loss spectroscopy, respectively. Furthermore, Schottky emission starts to control the conduction at lower electric fields after degradation as a result of oxygen vacancy accumulation near the cathode. This, in turn, decreases the potential barrier height for electron injection from the Pt electrode into the PZT films. The mechanisms for time-dependent dielectric breakdown in PZT films will thus be a strong function of the initial oxygen vacancy concentration and its distribution within the PZT films.
22 December 2017 in Journal of Applied Physics
Under electrical bias, mixed ionic conductors such as SrTiO3 are characterized by oxygen vacancy migration which leads to resistance degradation. The defect chemistry to describe the relationship between conductivity and oxygen vacancies is usually obtained by high temperature conductivity data or quenching experiments. These techniques can investigate the equilibrated state only. Here, we introduce a new approach using in-situ impedance studies with applied dc voltage to analyze the temperature dependent electrical properties of degraded SrTiO3 single crystals. This procedure is most beneficial since it includes electric field driven effects. The benefits of the approach are highlighted by comparing acceptor doped and undoped SrTiO3. This approach allows the determination of the temperature activation of both anodic and cathodic conductivity of Fe-doped SrTiO3 in the degraded state. The anodic activation energy matches well with the published results, while the activation energy of the degraded cathode region reported here is not in agreement with earlier assumptions. The specific discrepancies of the experimental data and the published defect chemistry are discussed, and a defect chemistry model that includes the strong temperature dependence of the electron conductivity in the cathode region is proposed.
26 June 2017 in Applied Physics Letters
Charge injection is a common phenomenon in heterostructures or devices containing metal-insulator interfaces under a voltage bias ranging from dielectric capacitors to electroluminescent and lasing devices. It is generally believed that charge injection only significantly increases the conductivity near the interfacial region or in capacitors with very thin dielectric layers. In this work, the impact of charge injection on bulk conductivity of a 0.5 mm thick Fe-doped SrTiO3 single crystal is investigated with a combination of experimental impedance measurements and computational modelling. It is found that the interfacial charge injection may increase the predicted bulk conductivity of a dielectric by more than one order of magnitude as a consequence of Schottky barrier height lowering.