Zhaoyang Song

Zhaoyang Song

Auto-generated profile, based on publicly available information

Zhaoyang Song

College of Engineering, Nanjing Agricultural University, Nanjing 210031, China

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
29 June 2020 in Coatings
Verified
Journal Article
Open access
PDF file
ZSZhaoyang Song
Zhaoyang Song
HZHongwen Zhang
Hongwen Zhang
XFXiuqing Fu
Xiuqing Fu
JLJinran Lin
Jinran Lin
MSMoqi Shen
Moqi Shen
SDShuanglu Duan
Shuanglu Duan
The objective of this study was to improve the surface properties, hardness, wear resistance and electrochemical corrosion resistance of #45 steel. To this end, Ni–P–ZrO2–CeO2 composite coatings were prepared on the surface of #45 steel using the jet-electrodeposition technique by varying the current density from 20 to 60 A/dm2. The effect of current density on the performance of the composite coatings was evaluated. Scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS) and X-ray diffraction (XRD) were applied to explore the surface topography, elemental composition, hardness and electrochemical corrosion resistance of the composite coatings. The results showed that with the increase in the current density, the hardness, wear resistance, and electrochemical corrosion resistance tends to increase first and then decrease. At a current density of 40 A/dm2, the hardness reached a maximum of 688.9 HV0.1, the corrosion current reached a minimum of 8.2501 × 10−5 A·cm−2, and the corrosion potential reached a maximum of −0.45957 V. At these values, the performance of the composite coatings was optimal.

29 October 2024 in Journal of Alloys and Compounds
Verified
Journal Article
Closed access
MPMingjun Pang
Mingjun Pang
ZSZhaoyang Song
Zhaoyang Song
SJShang Jiang
Shang Jiang
RZRuxia Zhang
Ruxia Zhang
YXYunlong Xi
Yunlong Xi
JZJianguo Zhao
Jianguo Zhao

11 May 2021 in Materials
Verified
Journal Article
Open access
PDF file
YGYanqing Gu
Yanqing Gu
HZHongwen Zhang
Hongwen Zhang
XFXiuqing Fu
Xiuqing Fu
LWLei Wang
Lei Wang
SZShen Zhenyu
Shen Zhenyu
LZLongchang Zhang
Longchang Zhang
This study aimed to investigate the wear failure changes of spindle hook teeth and the reasons for such failure during field work. Spindle samples were obtained from a fixed position of the spindle bar under different field picking area conditions and combined with the spatial distribution characteristics of cotton bolls in Xinjiang. After cutting a spindle sample, a scanning electron microscope and an energy spectrum analyzer were used to characterize the micromorphology and element composition of the hook tooth surface and cross section under different working area conditions. The wear parameters of the hook teeth were then extracted. The results showed that the thickness of the coating on the surface of the hook tooth used in this study was between 66.1 µm and 74.4 µm. The major chemical element was chromium, with a small amount of nickel. During the field picking process, failure of the coating on the surface of the hook teeth initially appeared on the tooth tip and tooth edge, and then spread to the entire hook tooth surface. The wear failure of the hook teeth resulted from abrasive wear, oxidative wear, and fatigue peeling. As the picking area increased, the wear area of the hook teeth increased exponentially, while the wear width increased linearly. When the field picking area reached 533.33 ha, the maximum change rate of the wear area was 2.33 × 103 µm2/ha, and the wear width was 1.84 µm/ha. During field work, the thickness of the coating decreased from the cutting surface to the tooth edge, and the wear rate gradually increased. The wear rate at Position 1 was the slowest, at 0.01 µm/ha, and the wear rate at Position 5 was the fastest, at 0.25 µm/ha.

11 November 2026 in International Journal of Extreme Manufacturing
Verified
Journal Article
Open access
PDF file
ZSZhaoyang Song
Zhaoyang Song
DZDi Zhu
Di Zhu
DWDengyong Wang
Dengyong Wang
The polishing of curved internal channels fabricated by metal additive manufacturing remains exceedingly challenging, primarily constrained by the limitations of the cathode structures and the intricate geometry of the internal channels. To address this issue, an electrochemical finishing method with a segmented multi-link cathode is proposed for the polishing of curved holes fabricated via selective laser melting. Simulation of the stress and offset amount revealed that the segmented multi-link cathode could flexibly bend to conform to the channel contour inside the curved hole. Moreover, the integration of the nylon brush facilitates the alignment of the center of the segmented multi-link cathode with that of the curved hole. In comparison, the monolithic twisted cathode showed a maximum offset amount of 0.21 mm, whereas the segmented multi-link cathode yielded negligible deviation. Current density distribution simulations further confirmed that a uniform side gap ensured a homogeneous current density distribution during electrochemical finishing. Such uniformity mitigates nonuniform material removal problems, such as overcut polishing and undercut polishing. Consequently, a curved hole with a diameter of 2 mm, a length of 60 mm and a curvature radius of 120 mm was successfully polished. The average surface roughness Ra was reduced from 11.36 μm to 1.59 μm. Meanwhile, the average roundness was improved from 0.138 mm (achieved via conventional electropolishing with a monolithic twisted cathode) to 0.011 mm using the proposed method. Furthermore, satisfactory finishing was achieved for spiral internal channels with variable curvature radii and reciprocal internal channels with small curvature radii. The average surface roughness Ra of the spiral and reciprocal internal channels are markedly reduced from 14.44 μm and 14.42 μm to 2.57 μm and 2.80 μm, respectively. Such a result cannot be attained using conventional electropolishing, thereby validating the superiority of the proposed method.