We report on the fabrication of photovoltaic cells, PVs, with controlled donor/acceptor interfaces using a process based on the phase separation between a cross-linkable polyfluorene and polystyrene. Robust, nanostructured columnar-grain layers of a conjugated cross-linked polymer, F8T2Ox1 (an oxetane-functionalized derivative of poly(9,9-dioctylfluorene-alt-bithiophene)) are obtained after removal of polystyrene. These layers are used, in combination with 1-(3-methoxycarbonyl)propyl-1-phenyl-(6,6)C61 (PCBM) deposited by spin coating, to define donor/acceptor interfaces, as PVs' active layers. The performance of these cells is dependent on the dimensions of the surface structures. In particular, a significant power conversion efficiency improvement is observed upon decrease of column diameter, reflecting an improvement of the exciton dissociation. We find, however, that these efficiencies still fall below those of the PVs based on blends of the same components, but are larger than the ones found for planar bilayer PVs. Furthermore, PVs based on blends of cross-linked F8T2Ox1 and PCBM showed enhanced efficiency and thermal stability with respect to PVs based on blends of PCBM and the non-cross-linkable analogue poly(9,9-dioctylfluorene-alt-bithiophene). Taking into account that the columnar-grain morphology is recognised as the “ideal” architecture for PVs' active layer provided the column radii are of the order of few nanometres, this work gives a new insight into how to achieve efficient organic photovoltaic cells through the use of cross-linkable conjugated polymers as the electron-donor component.
Ternary blend polymer solar cells combining two electron-donor polymers, poly[4,8-bis[(2-ethylhexyl)oxy]benzo[1,2-b:4,5-b′]dithiophene-2,6-diyl][3-fluoro-2-[(2-ethylhexyl)carbonyl]thieno[3,4-b]thiophenediyl] (PTB7) and poly[2,5-bis(3-dodecylthiophen-2-yl)thieno[3,2-b]thiophene] (pBTTT) and [6,6]-phenyl-C61-butyric acid methyl ester (PC61BM), as electron-acceptor, were fabricated. The power conversion efficiency of the ternary cells was enhanced by 18%, with respect to the reference binary cells, for a blend composition with 25% (wt%) of pBTTT in the polymers content. The optimized device performance was related to the blend morphology, nonrevealing pBTTT aggregates, and improved charge extraction within the device.
This paper describes an energy harvesting system composed of an organic photovoltaic cell (OPV) connected to a DC–DC converter, designed in a 130 nm Complementary Metal-Oxide-Semiconductor (CMOS) technology, with a quasi- maximum power point tracking (MPPT) algorithm to maximize the system efficiency, for indoor applications. OPVs are an emerging technology with potential for low cost indoor light energy harvesting. The OPV current-voltage curves (I-V) under an irradiance of solar simulator Oriel Sol 3A, at room temperature, are obtained and an accurate electrical model is derived. The energy harvesting system is subjected to four different indoor light sources: 35 W halogen, 3.5 W LED, 5 W LED, and 7 W LED, positioned at three different heights (0.45 m, 0.26 m, and 0.11 m), to evaluate the potential of the system for indoor applications. The measurements showed maximum efficiencies of 60% for 35 W halogen and 45% for 7 W LED at the highest distance (0.45 m) and between 60% (5 W LED) and 70% (35 W halogen), at the shorter distance (0.11 m). Under irradiation, the integrated CMOS circuit presented a maximum efficiency of 75.76%, which is, to the best of the authors’ knowledge, the best reported power management unit (PMU) energy system using organic photovoltaic cells.