6 March 2019 in IEEE Transactions on Components, Packaging and Manufacturing Technology
Integrated voltage regulators (IVR) support an increasing number of voltage domains while enhancing the transient response, enabling fine grained dynamic voltage frequency scaling. A VR-on-package is a promising IVR topology which supports high voltage transmission within a printed circuit board and package, leading to lower distribution loss. A power delivery network within a VR-on-package environment is presented in this paper. This paper also presents a study of VR top and bottom placement topologies within a system-in-package environment in terms of EMI and power integrity. This comparative analysis targets a specific server package application, and the power integrity evaluation is focused on the power delivery network between the VR and IC. The VR top placement topology exhibits more than 3X less EMI, and 15.3% lower worse case IR drop as compared with the VR bottom placement topology. The tradeoffs are however a larger package power loss and higher package cost due to the larger number of package layers in the VR top placement topology. The VR top placement topology exhibits a 52.6% higher power loss through the package than the VR bottom placement topology.
27 June 2019 in IEEE Transactions on Computer-Aided Design of Integrated Circuits and Systems
The conventional power network design process requires iterative modifications to the existing power network to eliminate hot spots and to converge to target impedance parameters. At later stages in the IC design process, this procedure may require significant time and human resources due to the limited flexibility to accommodate necessary changes. Power delivery exploration during early stages of the design process may bring considerable savings to the system development effort. The number of iterations may be greatly reduced by choosing the initial parameters sufficiently close to the optimum. The current work presents a power delivery exploration framework based on constrained global optimization. The power network parameters are estimated at early stages of the development process, while considering both electrical and non-electrical factors, such as area and cost. A Laplace transform-based circuit simulator is described that is well suited for optimization purposes due to the high computational efficiency when a large number of iterations is required. The proposed framework has been applied to the distribution of voltage domains in a large scale complex integrated system, while minimizing the cost of the decoupling capacitor placement. The optimal number of voltage rails are determined, demonstrating an approximately 40% lower on-chip area than alternative solutions.
24 March 2021 in IEEE Transactions on Components, Packaging and Manufacturing Technology
Although CMOS scaling has slowed, the demand for greater performance and heterogeneous integration has only increased. Three-dimensional integrated circuits (ICs), which exploit the vertical dimension, extend scaling while providing a platform for heterogeneous integration and greater performance. The redistribution layer (RDL) is a critical component in the power delivery system within heterogeneous 3-D systems, where each layer is individually designed, optimized, and fabricated. A circuit model of the power/ground (P/G) RDL is described considering different through-silicon-via (TSV) fabrication methods and stacking topologies. A grid-based RDL is proposed to support higher current and fewer P/G TSVs. By utilizing a grid-based RDL, five times more current is supported without a significant voltage drop as compared with a direct point-to-point (P2P) RDL. The grid-based RDL also supports a nonuniform TSV distribution, alleviating area constraints. In one case study, a grid-based RDL with 20 unevenly distributed TSVs exhibits a 9.8% lower voltage drop than a P2P RDL with 50 uniformly distributed TSVs.
18 June 2021 in IEEE Transactions on Components, Packaging and Manufacturing Technology
Due to the increasing throughput of high performance integrated circuits, the power consumption of recent high performance computing systems has grown significantly, leading to greater on-chip current demand. The large current flowing within the power delivery system produces challenging issues such as electromigration, low power efficiency, and thermal hotspots. To reduce on-chip current demand, voltage stacking has become a topic of growing interest within the industrial and academic communities. The challenges of power delivery for on-chip voltage stacked systems are however significant. The power delivery system connects individual stacks and stacks to converters. Challenges include cross-core current paths. A tile-based power delivery design methodology is proposed for high current, voltage stacked systems. The tile-based power delivery system provides net separation, low parasitic impedance, and a scalable design process. The tile shape eases the design and characterization of the parasitic impedance, making this methodology effective for early stage exploration of the power delivery system within voltage stacked structures.