Equilibria evolving over time, also called trends, are often present in ongoing measurements of real-life systems. These trends are considered as disturbances when computing the best linear time-varying approximation (BLTVA) of the system. Current techniques for dealing with trends in BLTVA measurements consist of modeling the trend with a finite number of basis functions. However, in measurements with dominant trends, the trend cannot always be captured well enough by this set of basis functions, and hence, the uncertainty on the BLTVA increases. As a consequence, one loses low-frequency information. In this article, the state-of-the-art method for estimating the BLTVA is extended by removing the trend with a differencing operator. It is shown that with this novel technique, low-frequency information becomes more visible. Moreover, the novel method decreases the variance on the BLTVA and allows to measure fewer periods. Hence, the novel technique improves the route for treating arbitrary out-of-equilibrium or also called operando, measurements. As an illustration, it is applied to operando time-varying impedance measurements of three electrochemical processes: the charging of a Li-ion battery cell, the electrorefining of copper, and the anodizing of aluminum.
This article presents a method for estimating a linear time-varying approximation of a general class of nonlinear time-varying (NLTV) systems. It starts from noisy measurements of the response of the NLTV system to a special class of periodic excitation signals. These measurements are subject to measurement noise, process noise, and a trend. The proposed method is a two-step procedure. First, the disturbing noise variance is quantified. Next, using this knowledge, the linear time-varying dynamics are estimated together with the NLTV distortions. The latter are split into even and odd contributions. As a result, the signal-to-nonlinear-distortion ratio is quantified. It allows one to decide whether or not a linear approximation is justifiable for the application at hand. The two-step algorithm is fully automatic in the sense that the user only has to choose upper bounds on the number of basis functions used for modeling the response signal. The obtained linear time-varying approximation is the best in the sense that the difference between the actual nonlinear response and the response predicted by the linear approximation is uncorrelated with the input. Therefore, it is called the best linear time-varying approximation (BLTVA). Finally, the theory is validated on a simulation example and illustrated on two measurement examples: the crystallographic pitting corrosion of aluminum and copper electrorefining.
Ni−W alloy films were electrodeposited from a gluconate aqueous bath at pH=5.0, at varying current densities and temperatures. While there is little to no difference in composition, i. e., all films possess ~12 at.% W, their activity at hydrogen evolution reaction (HER) in acidic medium is greatly influenced by differences in surface morphology. The kinetics of HER in 0.5 M H2SO4 indicates that the best performing film was obtained at a current density of −4.8 mA/cm2 and 50 °C. The Tafel slopes (b) and the overpotentials at a geometric current density of −10 mA/cm2 (η10) obtained for 200 cycles of linear sweep voltammetry (LSV) from a set of films deposited using different parameters were fed into a machine learning algorithm to predict optimum deposition conditions to minimize b, η10, and the degradation of samples over time. The optimum deposition conditions predicted by the machine learning model led to the electrodeposition of Ni−W films with superior performance, exhibiting b of 33–45 mV/dec and an η10 of 0.09–0.10 V after 200 LSVs.
26 August 2020 in IEEE Transactions on Instrumentation and Measurement
The class of nonlinear time-varying (NLTV) systems includes all possible systems and, hence, is difficult to identify. Still, when the nonlinearities are not too strong then, depending on the application, a linear model might be sufficient for approximating the true response. To quantify the approximation error of the linear model, detecting and quantifying the nonlinear behavior is of key importance. In this paper we propose a fully automated procedure for detecting, classifying and quantifying the nonlinear distortions in the response, possibly subject to a trend, of a specific class of NLTV systems to odd random phase multisine excitations. The result is a measurement of the time-varying frequency response function together with uncertainty bounds due to noise and nonlinear distortions. The user only has to specify four integer numbers: an upper bound on (i) the degree on the time-domain polynomial modelling of the trend, (ii) the degree of the frequency-domain polynomial basis function and (iii) the number of frequency-domain hyperbolic-like basis functions, all used for modeling the output spectrum; and (iv) a quality measure – called degrees-of-freedom – of the noise variance estimate. Guidelines are provided for obtaining reasonable values for these upper bounds.