This study evaluated the bone incorporation process of a screw-shaped internal fixation device made of poly (L-lactide-co-D, L-lactide) (PLDLLA). Thirty-two male Wistar rats received 32 fixation devices (2 mm × 6 mm) randomly assigned to either the right or left tibia and one implant in each animal. After 7, 14, 28, and 42 days, the rats were euthanized and the specimens were subjected to microtomographic computed tomography (microCT) and histomorphometric analyses to evaluate bone interface contact (BIC%) and new bone formation (NBF%) in cortical and cancellous bone areas. The animals euthanized on days 28 and 42 were treated with calcein and alizarin red, and confocal LASER microscopy was performed to determine the mineral apposition rate (MAR). Micro-CT revealed a higher percentage of bone volume (p < 0.006), trabecular separation (p < 0.001), and BIC in the cortical (p < 0.001) and cancellous (p = 0.003) areas at 28 and 42 days than at 7 and 14 days. The cortical NBF at 42 days was greater than that at 7 and 14 days (p = 0.022). No statistically significant differences were observed in cancellous NBF or MAR at 28 and 42 days. Based on these results, it can be seen that the PLDLLA internal fixation device is biocompatible and allows new bone formation around the screw thread.
27 March 2022 in Research, Society and Development
The aim of this study was to evaluate, through microscopic analysis, the repair of critical defects in rabbit calvaria after the use of particulate autogenous bone or particulate autogenous bone associated with inorganic biomaterial. Six male albino rabbits, New Zealand, were used, in which 4 defects were performed in each calvaria and randomly divided into 4 equitable groups: Group I – performed bone defect; Group II – performed bone defect and filled with particulate autogenous bone; Group III – performed bone defect and filled with particulate inorganic material (Bio-Oss®, Geistlich from Brazil); Group IV – performed bone defect and filled with particulate autogenous bone associated with particulate inorganic material (Bio-Oss® - Geistlich from Brazil) with proportion being 20:80. The analyze time of the procedure was 60 days. The microscopic analyze allowed to conclude that the autogenous, the Bio-Oss® and the Bio-Oss® associated with autogenous bone groups showed a bone neoformation on the defects, characterizing the material osteoconductive. However, the complete defect closure occurred on the autogenous bone and the autogenous bone associated with the inorganic bone, showing that the presence of the autogenous bone improves the characteristics of the biomaterial. The use of inorganic bone associated with the autogenous bone allowed a complete bone neoformation of the critic defect in the calvaria of rabbits.
The presence of foreign bodies in the maxillary sinus represents an uncommon, yet clinically relevant, complication in dental practice. Various objects can be displaced into this cavity, such as dental roots, intact teeth, dental implants, surgical burs, fragments of endodontic instruments, and filling materials. Accurate diagnosis supported by imaging and appropriate planning are essential to prevent infectious complications and ensure complete foreign body removal. This study presents four clinical cases of foreign bodies displaced into the maxillary sinus, which were successfully removed surgically through variations of the Caldwell-Luc approach, involving adequate exposure, copious irrigation, and suture closure. This resulted in favorable post-operative evolution and the absence of sinus complications. This study reinforces the importance of early diagnosis, individualized planning, and the careful selection of the surgical access route. The Caldwell-Luc access remains a safe, predictable, and effective technique for the removal of voluminous or difficult-to-access foreign bodies, maintaining its relevance even when facing contemporary minimally invasive approaches.
The selection of an appropriate fixation system is critical for maintaining postoperative stability after sagittal split ramus osteotomy (SSRO), especially in cases involving large mandibular advancements and counterclockwise rotation, where mechanical stresses may compromise treatment outcomes. This in vitro study evaluated the biomechanical stability of five fixation systems following sagittal split ramus osteotomy (SSRO) under two mandibular advancement conditions. Fifty polyurethane hemimandibles were allocated into two experimental groups: Group 1, submitted to 10-mm linear advancement, and Group 2, submitted to 10-mm advancement associated with 20° counterclockwise rotation. Each group was further divided into five subgroups according to the fixation design employed: (A) conventional straight plate, (B) angled plate, (C) sagittal plate, (D) 10-hole miniplate, and (E) two 4-hole miniplates. Biomechanical performance was assessed by compression testing using a universal testing machine. Complementary analyses were performed using strain gauges and digital image correlation. Group 1 in fixation B, C and D demonstrated higher biomechanical resistance than Group 2, however without significance difference. Among the evaluated configurations, subgroup E exhibited the highest resistance values in both experimental conditions. Statistically significant differences were observed among fixation systems within each group (p < 0.05). The fixation systems using two miniplates demonstrated superior biomechanical stability, particularly in mandibular advancements associated with counterclockwise rotational movements. These findings suggest that this fixation strategy may contribute to enhanced postoperative stability in orthognathic surgery involving large mandibular advancements and complex rotational movements.
4 January 2025 in Contribuciones A Las Ciencias Sociales
Objetivo: Relatar um caso clínico de remoção de tórus mandibular bilateral e osteoplastia para reabilitação oral com prótese parcial removível. Métodos: Paciente gênero feminino, 67 anos, apresentou por meio de exame clínico e radiográfico, tórus mandibular bilateral. A conduta definida foi exérese cirúrgica da exostose para viabilizar a reabilitação oral com prótese parcial removível. Foi realizado uma incisão sobre a crista alveolar, estendendo-se 1 cm além das margens do tórus. A osteoplastia foi realizada com broca maxicut montada em peça reta de mão. Sutura interrompida simples foi realizada com fio de nylon 4.0 na crista do rebordo e nas regiões papilares. Resultados: Neste caso, obteve-se sucesso na remoção total do tórus mandibular bilateral, o qual apresentou reparo tecidual sem comprometimento local ou complicação pós-operatória. A paciente seguiu com a reabilitação oral protética. Conclusão: A remoção cirúrgica de tórus mandibulares bilateral extensos se torna necessária para garantir a adaptação eficaz de próteses parciais removíveis como no caso relatado. Isso garante o restabelecimento funcional e estético e melhora a qualidade de vida do paciente.