Shengzhao Yang

Shengzhao Yang

Auto-generated profile, based on publicly available information

Shengzhao Yang

Aalto University

Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
15 December 2024 in Materials Science and Engineering: A
Verified
Journal Article
Open access
SYShengzhao Yang
Shengzhao Yang
YZYanjie Zhang
Yanjie Zhang
RJRongfei Juan
Rongfei Juan
ZLZinan Li
Zinan Li
JWJiaojiao Wu
Jiaojiao Wu
JLJunhe Lian
Junhe Lian

15 June 2026 in Research Square
Verified
Preprint
Open access
SYShengzhao Yang
Shengzhao Yang
EFEric Fangnon
Eric Fangnon
SSSiddharth Suman
Siddharth Suman
AAAmil Aligayev
Amil Aligayev
MHMiroslav Hustak
Miroslav Hustak
Mika SalmiMika Salmi
Mika Salmi
The development of green hydrogen as an energy carrier is hindered by hydrogen embrittlement (HE) from materials perspective. HE phenomenon leads to premature failure of metallic materials. Reducing HE while maintaining low production costs remains a major challenge for industry. In this study, the hydrogen behavior of 3D-printed AlSi10Mg was investigated, owing to its potential as a low-cost hydrogen storage material. A unique amorphous Al–Si eutectic structure, formed during the rapid melting and solidification process of 3D printing, was identified. Both simulations and experimental results revealed that hydrogen is preferentially trapped within this amorphous Al–Si eutectic structure. The non-crystalline nature of this phase promotes a more homogeneous hydrogen distribution in AlSi10Mg, thereby enhancing its resistance to HE compared with conventional Al-based alloys. For the first time, these findings provide fully new insights into the design of and mechanical performance of HE-resistant aluminum alloys containing amorphous structures formed through additive manufacturing processes.

13 November 2026 in Additive Manufacturing
Verified
Journal Article
Open access
SYShengzhao Yang
Shengzhao Yang
EFEric Fangnon
Eric Fangnon
SSSiddharth Suman
Siddharth Suman
Amil AligayevAmil Aligayev
Amil Aligayev
MHMiroslav Husťák
Miroslav Husťák
MSMika Salmi
Mika Salmi

17 March 2026 in SSRN Electronic Journal
Verified
Preprint
Open access
SASadique Ali
Sadique Ali
RBRoy Björkstrand
Roy Björkstrand
SKS. Siddharth Kumar
S. Siddharth Kumar
SYShengzhao Yang
Shengzhao Yang
TPTuomas Puttonen
Tuomas Puttonen
MSMika Salmi
Mika Salmi
Limited productivity remains a barrier to the broader adoption of additive manufacturing, particularly in Laser-based powder bed fusion for metals (PBF-LB/M). For AlSi10Mg alloys, the high volumetric energy density required to overcome high reflectivity leaves limited room for productivity improvement. This study demonstrates that TiN nanoparticle reinforcement improves energy absorption, enabling concurrent increases in productivity and similar or advanced mechanical performance. A systematic design of experiments was developed to assess the influence of processing parameters on build rate while maintaining material properties. The optimal TiN content was identified as 2 wt.%, at which the additively manufactured specimens exhibited a high build rate with good mechanical properties. Compared with virgin AlSi10Mg manufactured at a build rate of 5.07 mm3/s (UTS: 427.7 MPa), the optimum condition achieved 54% enhancement in build rate (7.8 mm3/s) while yielding an improved UTS of 464.8 ± 6.0 MPa (~8.7% higher). Further increasing the build rate to 10.14 mm3/s enabled a ~100% productivity gain but reduced the UTS to 373.2 ± 13.6 MPa (~13% lower), thereby revealing the process–property trade-off. Overall, TiN addition widens the processing window of AlSi10Mg, enabling increased productivity of PBF-LB/M aluminium matrix composites (AMCs) without hardware modifications.