Jing Jin

Jing Jin

Auto-generated profile, based on publicly available information

Jing Jin

Shanghai Jiao Tong University

Research Focus & Metrics

Academic Career Length

17Years (2010-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
28 September 2022 in IEEE Transactions on Microwave Theory and Techniques
Verified
Journal Article
Closed access
XLXiaoming Liu
Xiaoming Liu
CYChao Yang
Chao Yang
ZYZhaolin Yang
Zhaolin Yang
YGYuekang Guo
Yuekang Guo
JJJing Jin
Jing Jin
JZJianjun Zhou
Jianjun Zhou
An area-efficient 28-GHz four-element phased-array transceiver front-end (TRx FE) is proposed in this article. Transmitter/receiver (T/R) switch, phase shifter (PS), and power combining/splitting network all use customized coupler-based structures to replace area-consuming quarter-wavelength ( $\lambda $ /4) transmission line (T-line) structures. In Tx mode, a three-stage power amplifier (PA) is designed by cascading a class-AB predriver amplifier, a deep class-AB driver amplifier, and a class-A output amplifier for high output power. In Rx mode, a two-stage low noise amplifier (LNA) is designed with a 3-bit resistive adjusting load for high dynamic range of input power. A coupler is adopted in the variable gain amplifier (VGA) to achieve constant phase during gain adjustment. The proposed TRx FE is fabricated in a 40-nm CMOS process. Measurement results show that output 1-dB compression point (OP1dB) of 14.99 dBm and saturated output power (OPsat) of 15.68 dBm with 25.2% power efficiency are achieved in each Tx element. In each Rx element, noise figure (NF) of 4.54 dB, input 1-dB compression point (IP1dB) of $-$ 10.15 dBm, and maximum gain of 26.3 dB with 56.1-mW power consumption are realized. The gain range of Rx/Tx mode is 9.9–26.3 dB/24.2–44.6 dB with a resolution of 0.3 dB and phase variation less than 2 $^{\circ}$ at 28 GHz. Thanks to the area-efficient coupler-based structures, the phased-array TRx FE occupies an area of 0.42 mm $^{2}$ for each element and 0.084 mm $^{2}$ for total area of combiner/splitter, achieving high area efficiency for Ka-band phased-array TRx FEs.

23 July 2020 in IEEE Transactions on Circuits and Systems I: Regular Papers
Verified
Journal Article
Closed access
YGYuekang Guo
Yuekang Guo
JJJing Jin
Jing Jin
XLXiaoming Liu
Xiaoming Liu
JZJianjun Zhou
Jianjun Zhou
This paper presents a wide bandwidth inverter-based continuous time sigma delta (CTSD) analog-to-digital converter (ADC) with a latency-free calibration to suppress the nonlinearity originating from the feedback digital-to-analog converter (DAC). The modulator in the ADC uses a fourth-order architecture with 4-bit quantization. To compensate the excess loop delay (ELD), the proportional-integrating element (PI-element) is employed in the loop filter where the problem of no real solution in conventional PI-element compensation method is solved. In addition, the two-stage inverter-based amplifiers are used in the loop filter to improve power efficiency. To suppress nonlinearity of the 4-bit DAC, a background calibration method based on modified quantizer is proposed which would not introduce additional latency thus ensuring stability of the modulator. The CTSD ADC achieves 64.6 dB SNDR and 71.2 dB SFDR over a 75 MHz signal bandwidth before calibration, and the SNDR and the SFDR can be improved to 67.3 dB and 82.3 dB respectively after calibration. The ADC consumes 38 mW from supply voltages of 1.1/1.8 V with an active area of 0.675 mm² in 40 nm CMOS.

29 June 2022 in IEEE Journal of Solid-State Circuits
Verified
Journal Article
Closed access
YGYuekang Guo
Yuekang Guo
JJJing Jin
Jing Jin
XLXiaoming Liu
Xiaoming Liu
JZJianjun Zhou
Jianjun Zhou
This article presents a 60-MS/s 5-MHz BW noise-shaping (NS) successive-approximation-register (SAR) analog-to-digital converter (ADC) with an integrated highly linear input buffer in a 40-nm CMOS process. A dynamic level-shifting (DLS) technique is proposed to adaptively adjust the output common-mode voltage of the integrated input buffer for different operation phases, achieving the optimal linearity while alleviating the voltage breakdown problem at the capacitive digital-to-analog converter (CDAC) top plate. The mismatch-error-shaping (MES) technique is utilized to minimize the CDAC mismatch, which also generates undesired inter-symbol-interference (ISI) errors as a side effect. An ISI-error correction (IEC) technique is proposed to mitigate this problem and further improve the linearity. Both foreground and background calibrations are adopted in the subranging ADC and the NS filter to improve the gain accuracy. This SAR ADC prototype, with an integrated input buffer driving a 4.4-pF CDAC within 2.7 ns, achieves signal-to-noise ratio (SNR)/signal-to-noise-and-distortion ratio (SNDR)/spurious-free dynamic range (SFDR)/dynamic range (DR)/total harmonic distortion (THD) of 85.4 dB/84.2 dB/97.3 dBc/86.4 dB/−92.9 dBc while consuming 8.06 mW from 2.5- and 1.1-V dual supply voltages. The Walden FoM (FoM $_{\mathrm {W}}$ ) and figure-of-merit (FoM $_{\mathrm {S}}$ ) are 60.6 fJ/conv.-step and 172.1 dB, respectively.

25 April 2018 in IET Circuits, Devices & Systems
Verified
Journal Article
Open access
PDF file
RGRui Guan
Rui Guan
JXJianfeng Xue
Jianfeng Xue
CYChao Yang
Chao Yang
JJJing Jin
Jing Jin
JZJianjun Zhou
Jianjun Zhou
This study presents a low‐power 16‐bit 1‐MS/s successive approximation register analogue‐to‐digital converter (SAR ADC) for medical instrument applications. A foreground digital‐domain calibration method simultaneously correcting mismatch errors in capacitive digital‐to‐analogue converter (CDAC) and ‘segment error’ of split‐CDAC array is proposed. The split‐CDAC architecture combines a V cm ‐free technique in a floating CDAC scheme. The V cm ‐free technique avoids a power hungry V cm generator, and the floating CDAC scheme allows the conversion of a high‐voltage input signal with low supply voltage and without a significant attenuation of the input signal. Moreover, a modified direct‐switching SAR logic is adopted to improve the conversion speed. The prototype was fabricated in a 0.18 µm 1P6M Complementary Metal Oxide Semiconductor (CMOS) technology, and achieves 86.16 dB signal‐to‐noise and distortion ratio and an Figure of Merit (FOM) of 0.41 pJ/conversion‐step.

5 April 2023 in IEEE Journal of Solid-State Circuits
Verified
Journal Article
Closed access
YGYuekang Guo
Yuekang Guo
JJJing Jin
Jing Jin
XLXiaoming Liu
Xiaoming Liu
JZJianjun Zhou
Jianjun Zhou
This article presents a nested delta-sigma modulator (DSM) structure, where an inner analog DSM is embedded in an outer analog-digital-hybrid DSM. The outer hybrid DSM is composed of the inner analog DSM, a digital filter, and a hysteresis-comparison MSB-pass quantizer. The internal signal swing of the inner analog DSM can be significantly suppressed by the outer DSM loop, thus achieving good power efficiency. Compared to conventional system-level signal swing optimization techniques, the proposed nested DSM does not suffer from residual signal error issues and distortion leakage and is more digital-friendly with great flexibility. Fabricated in a 180 nm CMOS, the prototype analog-to-digital converter (ADC), using the nested DSM structure with hysteresis-comparison MSB-pass quantization, achieves signal-to-noise ratio (SNR)/signal-to-noise-and-distortion ratio (SNDR)/spurious-free dynamic range (SFDR)/dynamic range (DR) of 110 dB/109.2 dB/119.6 dBc/110.3 dB, respectively. It achieves a measured Schreier figure of merit (FoM $_{\mathrm{S}})$ of 183.5 dB, which is among the best FoM $_{\mathrm{S}}$ of the state-of-the-arts.

25 July 2022 in IEEE Transactions on Circuits and Systems I: Regular Papers
Verified
Journal Article
Closed access
YGYuekang Guo
Yuekang Guo
JJJing Jin
Jing Jin
XLXiaoming Liu
Xiaoming Liu
JZJianjun Zhou
Jianjun Zhou
This paper presents a continuous-time sigma-delta modulator (CTSDM) with a voltage-controlled-oscillator-based (VCO-based) integrating quantizer. A background replica-based calibration technique is proposed to alleviate the impact of the process, voltage supply, and temperature (PVT) variations on the tuning characteristic and current consumption of the VCO-based quantizer. Matching between the replica VCO and the main VCO in the proposed calibration is not needed. A latency-free background calibration technique is also proposed to eliminate the distortions caused by the DAC mismatch. The prototype VCO-based CTSDM is fabricated in a 40 nm CMOS and achieves SNDR/SFDR/DR of 76.4 dB/91.7 dBc/79.6 dB, respectively, within a 50 MHz bandwidth (BW) at 1.6 GHz sampling frequency. The measured SNDR varies within $\pm$ 1 dB over a temperature range of 0 $\sim$ 80 $^{\circ}$ C and a voltage supply variation of $\pm$ 10%, across different tested samples. The power consumption is 18.1 mW, achieving a Schreier Figure of Merit (FoM $_{\text{S}}$ ) of 170.8 dB.