28 September 2022 in IEEE Transactions on Microwave Theory and Techniques
An area-efficient 28-GHz four-element phased-array transceiver front-end (TRx FE) is proposed in this article. Transmitter/receiver (T/R) switch, phase shifter (PS), and power combining/splitting network all use customized coupler-based structures to replace area-consuming quarter-wavelength ( $\lambda $ /4) transmission line (T-line) structures. In Tx mode, a three-stage power amplifier (PA) is designed by cascading a class-AB predriver amplifier, a deep class-AB driver amplifier, and a class-A output amplifier for high output power. In Rx mode, a two-stage low noise amplifier (LNA) is designed with a 3-bit resistive adjusting load for high dynamic range of input power. A coupler is adopted in the variable gain amplifier (VGA) to achieve constant phase during gain adjustment. The proposed TRx FE is fabricated in a 40-nm CMOS process. Measurement results show that output 1-dB compression point (OP1dB) of 14.99 dBm and saturated output power (OPsat) of 15.68 dBm with 25.2% power efficiency are achieved in each Tx element. In each Rx element, noise figure (NF) of 4.54 dB, input 1-dB compression point (IP1dB) of $-$ 10.15 dBm, and maximum gain of 26.3 dB with 56.1-mW power consumption are realized. The gain range of Rx/Tx mode is 9.9–26.3 dB/24.2–44.6 dB with a resolution of 0.3 dB and phase variation less than 2 $^{\circ}$ at 28 GHz. Thanks to the area-efficient coupler-based structures, the phased-array TRx FE occupies an area of 0.42 mm $^{2}$ for each element and 0.084 mm $^{2}$ for total area of combiner/splitter, achieving high area efficiency for Ka-band phased-array TRx FEs.
29 June 2022 in IEEE Journal of Solid-State Circuits
This article presents a 60-MS/s 5-MHz BW noise-shaping (NS) successive-approximation-register (SAR) analog-to-digital converter (ADC) with an integrated highly linear input buffer in a 40-nm CMOS process. A dynamic level-shifting (DLS) technique is proposed to adaptively adjust the output common-mode voltage of the integrated input buffer for different operation phases, achieving the optimal linearity while alleviating the voltage breakdown problem at the capacitive digital-to-analog converter (CDAC) top plate. The mismatch-error-shaping (MES) technique is utilized to minimize the CDAC mismatch, which also generates undesired inter-symbol-interference (ISI) errors as a side effect. An ISI-error correction (IEC) technique is proposed to mitigate this problem and further improve the linearity. Both foreground and background calibrations are adopted in the subranging ADC and the NS filter to improve the gain accuracy. This SAR ADC prototype, with an integrated input buffer driving a 4.4-pF CDAC within 2.7 ns, achieves signal-to-noise ratio (SNR)/signal-to-noise-and-distortion ratio (SNDR)/spurious-free dynamic range (SFDR)/dynamic range (DR)/total harmonic distortion (THD) of 85.4 dB/84.2 dB/97.3 dBc/86.4 dB/−92.9 dBc while consuming 8.06 mW from 2.5- and 1.1-V dual supply voltages. The Walden FoM (FoM $_{\mathrm {W}}$ ) and figure-of-merit (FoM $_{\mathrm {S}}$ ) are 60.6 fJ/conv.-step and 172.1 dB, respectively.
5 April 2023 in IEEE Journal of Solid-State Circuits
This article presents a nested delta-sigma modulator (DSM) structure, where an inner analog DSM is embedded in an outer analog-digital-hybrid DSM. The outer hybrid DSM is composed of the inner analog DSM, a digital filter, and a hysteresis-comparison MSB-pass quantizer. The internal signal swing of the inner analog DSM can be significantly suppressed by the outer DSM loop, thus achieving good power efficiency. Compared to conventional system-level signal swing optimization techniques, the proposed nested DSM does not suffer from residual signal error issues and distortion leakage and is more digital-friendly with great flexibility. Fabricated in a 180 nm CMOS, the prototype analog-to-digital converter (ADC), using the nested DSM structure with hysteresis-comparison MSB-pass quantization, achieves signal-to-noise ratio (SNR)/signal-to-noise-and-distortion ratio (SNDR)/spurious-free dynamic range (SFDR)/dynamic range (DR) of 110 dB/109.2 dB/119.6 dBc/110.3 dB, respectively. It achieves a measured Schreier figure of merit (FoM $_{\mathrm{S}})$ of 183.5 dB, which is among the best FoM $_{\mathrm{S}}$ of the state-of-the-arts.
25 July 2022 in IEEE Transactions on Circuits and Systems I: Regular Papers
This paper presents a continuous-time sigma-delta modulator (CTSDM) with a voltage-controlled-oscillator-based (VCO-based) integrating quantizer. A background replica-based calibration technique is proposed to alleviate the impact of the process, voltage supply, and temperature (PVT) variations on the tuning characteristic and current consumption of the VCO-based quantizer. Matching between the replica VCO and the main VCO in the proposed calibration is not needed. A latency-free background calibration technique is also proposed to eliminate the distortions caused by the DAC mismatch. The prototype VCO-based CTSDM is fabricated in a 40 nm CMOS and achieves SNDR/SFDR/DR of 76.4 dB/91.7 dBc/79.6 dB, respectively, within a 50 MHz bandwidth (BW) at 1.6 GHz sampling frequency. The measured SNDR varies within $\pm$ 1 dB over a temperature range of 0 $\sim$ 80 $^{\circ}$ C and a voltage supply variation of $\pm$ 10%, across different tested samples. The power consumption is 18.1 mW, achieving a Schreier Figure of Merit (FoM $_{\text{S}}$ ) of 170.8 dB.
22 November 2023 in IEEE Transactions on Circuits and Systems I: Regular Papers
This article presents an energy-efficient single-ended transceiver featuring the proposed AC/DC-coupled pre-emphasis feed-forward equalizer (PE-FFE) and edge-dependent phase-modulation decision feedback equalizer (PM-DFE) for low-power memory controllers. Specifically: 1) on the transmitter (Tx) side, an AC/DC-coupled PE-FFE is implemented in a ground-terminated Tx to minimize the equalization (EQ) power and maximize the output swing; 2) on the receiver (Rx) side, an edge-dependent PM-DFE operating on the full-swing signal edges is proposed for time-domain EQ, which improves sampling margin and reduces the linear EQ requirement as well as the power consumption. The design, fabricated in 22-nm CMOS, achieves a data rate of 20 Gb/s/pin with a 41 mV increase in the Tx output eye height and a 0.12 UI increase in the Rx sampling margin over a channel with a 10.3 dB loss. Measurement results reveal an energy efficiency of 0.45 pJ/b and 0.38 pJ/b for the Tx and the Rx, respectively, and a figure-of-merit of 0.081 pJ/b/dB (Tx $+$ Rx).
25 May 2022 in IEEE Transactions on Circuits and Systems II: Express Briefs
A fast-settling phase-locked loop (PLL) adopting the cycle-slipping-elimination phase frequency detector and charge pump (CSE-PFDCP) is presented. The CSE-PFDCP solves the cycle-slipping problem in a conventional non-linear PFDCP (NL-PFDCP), which accelerates the settling speed of the PLL. In addition, the metastability problem of the proposed cycle-slipping-elimination technology is analyzed in this brief. The proposed fast-settling PLL is fabricated in a 180 nm CMOS process with core area of 0.38 mm2. The frequency range of the PLL prototype is 2.1-2.6 GHz. Using the proposed CSE-PFDCP, the settling time is less than 6 $\mu \text{s}$ when the PLL frequency jump is 480 MHz, and the PLL settling speed is increased by 171%.