14 March 2016 in Smart Materials and Structures
This paper presents a small-scale airflow energy harvester built on an axial turbine architecture and exploiting an electret-based electrostatic converter. When the airflow velocity is high enough, the windmill starts rotating and creates a periodic relative motion between a stator and a rotor which induces variations of capacitance. These ones are directly converted into electricity thanks to the use of Teflon electrets charged at −1400 V which polarize the variable capacitors. We focus our study on a 4-blade axial turbine with a diameter of D = 40 mm, a depth of W = 10 mm, for a total volume of 12.6 cm 3 . This windmill has been tested with various blade angles and different types of electrostatic converters and output powers up to 90 μ W at 1.5 m s −1 (7.5 μ W cm −3 ) and 1.8 mW at 10 m s −1 (111 μ W cm −3 ) have been obtained so far. The coefficient of power reaches C p = 5.8% and among the small-scale airflow energy harvesters previously reported, this one has the lowest cut-in speed (1.5 m s −1 ).
3 February 2015 in Smart Materials and Structures
This paper presents a new airflow energy harvester exploiting fluttering effects coupled to an electret-based conversion to turn the flow-induced movements of a membrane into electricity. The proposed device is made of a polymer membrane placed between two parallel flat electrodes coated with 25 μ m thick Teflon PTFE electret layers; a bluff body is placed at the inlet of the device to induce vortex shedding. When the wind or airstream of any kind flows through the harvester, the membrane enters in oscillation due to fluttering and successively comes into contact with the two Teflon-coated fixed electrodes. This periodic motion is directly converted into electricity thanks to the electret-based conversion process. Various geometries have been tested and have highlighted a 2.7 cm 3 device, with an output power of 481 μ W (178 μ W cm −3 ) at 15 m s −1 and 2.1 mW (782 μ W cm −3 ) at 30 m s −1 with an electret charged at −650 V. The power coefficient C
p
of the device reaches 0.54% at 15 m s −1 which is low, but compares favorably with the other small-scale airflow energy harvesters.
7 February 2017 in Smart Materials and Structures
This paper reports on a method to optimize an electromagnetic energy harvester converting the low-frequency body motion and aimed at powering wireless body area sensors. This method is based on recorded accelerations, and mechanical and transduction models that enable an efficient joint optimization of the structural parameters. An optimized prototype of 14.8 mmØ × 52 mm, weighting 20 g, has generated up to 4.95 mW in a resistive load when worn at the arm during a run, and 6.57 mW when hand-shaken. Among the inertial electromagnetic energy harvesters reported so far, this one exhibits one of the highest power densities (up to 730 μ W cm −3 ). The energy harvester was finally used to power a bluetooth low energy wireless sensor node with accelerations measurements at 25 Hz.
1 June 2020 in Mechanical Systems and Signal Processing
12 December 2017 in Smart Materials and Structures
This paper presents the performances of several electrostatic flutter energy harvesters tested in a wind tunnel between 0 and 20 m s −1 . The main idea is to use the flutter capability of thin flexible films confined between lateral walls to induce simultaneously the capacitance variations and the electrostatic polarization required by the triboelectric/electrostatic conversion. This technology provides thin and flexible devices and solve the electret’s stability issue (Perez et al 2015 Smart Mater. Struct. , Perez et al 2015 New Circuits and Systems ). Our prototypes (<16 cm 2 ) have a quick startup (from 3 m s −1 ) and an electrical power-flux density from 0.35 μ W cm −2 @3 m s −1 (light breeze) to 35 μ W cm −2 @20 m s −1 (fresh gale). A Maximum Power Point circuit has been developed to efficiently use the power provided by the energy harvesters. The energy harvester combined with its power management circuit has finally been used to supply an 868 MHz wireless sensor node with temperature and acceleration measurements, validating the complete energy harvesting chain.
1 November 2016 in Journal of Physics: Conference Series
This paper deals with a rotational energy harvester including a Horizontal Axis Wind Turbine (HAWT), a cylindrical stator covered by several electrodes, and thin Teflon dielectric membranes hung on the rotor. The sliding contact of the Teflon membranes on the stator provides simultaneously large capacitance variations and a polarization source for the electrostatic converter by exploiting triboelectric phenomena. 1µW has been harvested at 4m/s; 130µW at 10m/s and 550µW at 20m/s with a 40mmØ device. In order to validate the energy harvesting chain, the airflow energy harvester has been connected to a power management circuit implementing Synchronous Electric Charge Extraction (SECE) to supply a wireless sensor node with temperature and acceleration measurements, transmitted to a computer at 868MHz.