Simon Chesne

Simon Chesne

Auto-generated profile, based on publicly available information

Simon Chesne

INSA Lyon, CNRS, LaMCoS, UMR5259, 69621 Villeurbanne, France

Research Focus & Metrics

Academic Career Length

19Years (2008-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 June 2020 in Mechanical Systems and Signal Processing
Verified
Journal Article
Closed access
MPM. Perez
M. Perez
SCS. Chesné
S. Chesné
CJC. Jean-Mistral
C. Jean-Mistral
KBK Billon
K Billon
RAR. Augez
R. Augez
CCC. Clerc
C. Clerc

11 July 2019 in Structural Control and Health Monitoring
Verified
Journal Article
Closed access
PDF file
SZShaoyi Zhou
Shaoyi Zhou
CJClaire Jean‐Mistral
Claire Jean‐Mistral
SCSimon Chesne
Simon Chesne

7 February 2022 in Journal of Vibration and Acoustics
Verified
Journal Article
Closed access
PDF file
JRJonathan Rodriguez
Jonathan Rodriguez
MCManuel Collet
Manuel Collet
SCSimon Chesné
Simon Chesné
This article proposes an active modal vibration control method based on a modal sliding mode controller applied to a smart material composite structure with integrated piezoelectric transducers as actuators and sensors. First, the electromechanical coupled system is identified using a modal reduced-order model. The sliding surface is based on the modal-filtered states and designed using a general formulation allowing the control of multiple vibration modes with multiple piezoelectric sensors and actuators. The performance and stability of the nonlinear controller are addressed and confirmed with the experimental results on a composite smart spoiler-shaped structure. The nonlinear switching control signal based on the modal-shaped sliding surface improves performances of the linear part of the control while maintaining not only stability but also robustness. The attenuation level achieved on the target modes on all piezoelectric sensors starts from −14 dB up to −22 dB, illustrating the strong potential of nonlinear switching control methods in active vibration control.

28 September 2020 in Journal of Vibration and Acoustics
Verified
Journal Article
Closed access
PDF file
APAhmad Paknejad
Ahmad Paknejad
GZguoying Zhao
guoying Zhao
SCSimon Chesné
Simon Chesné
ADArnaud Deraemaeker
Arnaud Deraemaeker
CCChristophe Collette
Christophe Collette
It has been shown that shunting electromagnetic devices with electrical networks can be used to damp vibrations. These absorbers have however limitations that restrict the control performance, i.e., the total damping of the system and robustness versus parameter variations. On the other hand, the electromagnetic devices are widely used in active control techniques as an actuator. The major difficulty that arises in practical implementation of these techniques is the power consumption required for conditioners and control units. In this study, robust hybrid control system is designed to combine the passive electromagnetic shunt damper with an active control in order to improve the performance with low power consumption. Two different active control laws, based on an active voltage source and an active current source, are proposed and compared. The control law of the active voltage source is the direct velocity feedback. However, the control law of the active current source is a revisited direct velocity feedback. The method of maximum damping, i.e., maximizing the exponential time-decay rate of the response subjected to the external impulse forcing function, is employed to optimize the parameters of the passive and the hybrid control systems. The advantage of using the hybrid control configuration in comparison with purely active control system is also investigated in terms of the power consumption. Besides these assets, it is demonstrated that the hybrid control system can tolerate a much higher level of uncertainty than the purely passive control systems.

22 May 2019 in Smart Materials and Structures
Verified
Journal Article
Closed access
PDF file
FMFabien Maugan
Fabien Maugan
SCSimon Chesne
Simon Chesne
MMMelodie Monteil
Melodie Monteil
MCManuel Collet
Manuel Collet
KYKaijun Yi
Kaijun Yi
The purpose of this paper is to highlight the interest of associating smart functionalities in the same smart-structure. It consists in combining a wave trap device with an energy harvester on a beam. Both functions are performed using piezoelectric transducers. The wave trap device is based on the acoustical black hole concept. It is designed to generate a gradual modification of the equivalent composite Young’s modulus along the beam. The aim is to concentrate the mechanical energy at the beam center where the harvesting device is placed. To achieve this, a network of transducers is used. The transducers are shunted on a specific negative capacitance. The harvester device is made of a simple piezoelectric patch associated with a classical extracting circuit. A significant increase in harvested energy is observed using this association for both weak and strong coupling. From the practical viewpoint, the study also highlights the sensitivity of the structural behavior, which strongly depends on the tuning of the trap device.

1 August 2022 in Mechanics & Industry
Verified
Journal Article
Open access
PDF file
MPMatthias Perez
Matthias Perez
KBKevin Billon
Kevin Billon
TGTony Gerges
Tony Gerges
JCJean-Fabien Capsal
Jean-Fabien Capsal
MCMichel Cabrera
Michel Cabrera
CJClaire Jean-Mistral
Claire Jean-Mistral
The aim of this publication is to conclude on the interest of vibratory energy harvesting on classic quadcopter drone for autonomous applications (battery charging in real time, autonomous sensors), monitoring or even vibration control applications. A complete dynamic analysis allows to quantify the amount of electrical power that is possible to produce during the hovering flight of a quadcopter drone. These results have been obtained by substitution of the inert parts of the drone by piezoelectric components. For that purpose, different types of piezoelectric structures have been tested, including some commercial transducers (DuraAct from Piezoelectric Instrument and Murata buzzers) and some home-made such as a piezoelectric paint. Our original piezoelectric smart arms have been able to scavenge up to 5.35 mW during a stationary flight which remains quite enough to supply low-consumption sensors for monitoring applications.