Rutile (TiO2) is an important host phase for high field strength elements (HFSE) such as Nb in metamorphic and subduction zone environments. The observed depletion of Nb in arc rocks is often explained by the hypothesis that rutile sequesters HFSE in the subducted slab and overlying sediment, and is chemically inert with respect to aqueous fluids evolved during prograde metamorphism in the forearc to subarc environment. However, field observations of exhumed terranes, and experimental studies, indicate that HFSE may be soluble in complex aqueous fluids at high pressure (i.e., >0.5 GPa) and moderate to high temperature (i.e., >300 °C). In this study, we investigated experimentally the mobility of Nb in NaCl- and NaF-bearing aqueous fluids in equilibrium with Nb-bearing rutile at pressure-temperature conditions applicable to fluid evolution in arc environments. Niobium concentrations in aqueous fluid at rutile saturation were measured directly by using a hydrothermal diamond-anvil cell (HDAC) and synchrotron X-ray fluorescence (SXRF) at 2.1 to 6.5 GPa and 300–500 °C, and indirectly by performing mass loss experiments in a piston-cylinder (PC) apparatus at ~1 GPa and 700–800 °C. The concentration of Nb in a 10 wt% NaCl aqueous fluid increases from 6 to 11 μg/g as temperature increases from 300 to 500 °C, over a pressure range from 2.1 to 2.8 GPa, consistent with a positive temperature dependence. The concentration of Nb in a 20 wt% NaCl aqueous fluid varies from 55 to 150 μg/g at 300 to 500 °C, over a pressure range from 1.8 to 6.4 GPa; however, there is no discernible temperature or pressure dependence. The Nb concentration in a 4 wt% NaF-bearing aqueous fluid increases from 180 to 910 μg/g as temperature increases from 300 to 500 °C over the pressure range 2.1 to 6.5 GPa. The data for the F-bearing fluid indicate that the Nb content of the fluid exhibits a dependence on temperature between 300 and 500 °C at ≥2 GPa, but there is no observed dependence on pressure. Together, the data demonstrate that the hydrothermal mobility of Nb is strongly controlled by the composition of the fluid, consistent with published data for Ti. At all experimental conditions, however, the concentration of Nb in the fluid is always lower than coexisting rutile, consistent with a role for rutile in moderating the Nb budget of arc rocks.
The dimensions of relatively small‐scale impact craters are undoubtedly sensitive to the physical properties of the target. Studying gravity‐controlled crater formation at the laboratory scale often relies on cohesionless, granular materials, which, by their nature, make it difficult to separate the individual contributions to this process from all of the relevant target properties. Here, we conduct a suite of impact experiments to isolate and evaluate the effects of density, porosity, and internal friction on impact crater morphometry. Each made from one of four different granular materials, targets were impacted vertically with 4.76 mm aluminum projectiles at an average speed of ~1.55 km s−1. Two different methods were used to load these materials into the target bucket (pouring and sieving), resulting in targets that varied in bulk density and internal friction. The experimental results indicate that depth–diameter ratios of the craters are largely influenced by the loading method of the target material and are sensitive to the friction and porosity of the targets. Sieved targets (relatively higher density, lower porosity, and higher friction angle) produce craters that are markedly shallower, have notably smaller volumes, and exhibit a flat‐floored morphology, with some possessing small central mounds. Flat‐floored craters are typically attributed to a strength‐layered target; in these experiments, however, they were produced in cohesionless targets. This study demonstrates that a flat floor is not necessarily diagnostic of strength layering in a target and, in some instances, might be the consequence of greater shear strengths in granular materials with high coefficients of static friction.
1 May 2013 in American Mineralogist: Journal of Earth and Planetary Materials
We have used electron backscatter diffraction (EBSD) to characterize the internal deformation and orientation of olivine grains within an experimentally deformed Mg2GeO4 olivine aggregate. We observe that a significant fraction of the grains contain kink bands. Our observations of kink band geometry, combined with the work of earlier authors, indicate that [001] slip is the dominant slip system operating in Mg2GeO4 olivine at 1000–1473 K at 0.6–1.3 GPa. Since Mg2GeO4 is a high-pressure analog for natural compositions of olivine, this is consistent with the observations made by others that the dominant slip system for olivine in the mantle switches from [100] to [001] as pressure increases. We also observed that kink bands formed in all measured olivine grains with [001] axes oriented within 35° of the compression direction. We thus conclude that in a randomly oriented polycrystal undergoing uniaxial deformation at low to moderate temperatures, 18% of all grains will deform by kinking and that kink band formation is an important accommodation mechanism for olivine at these conditions.
28 December 2017 in Physics and Chemistry of Minerals