Lars Schubert

Lars Schubert

Auto-generated profile, based on publicly available information

Lars Schubert

Fraunhofer IKTS Maria-Reiche Straße 2 01109 Dresden Germany

Research Focus & Metrics

Academic Career Length

20Years (2007-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
31 May 2021 in IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control
Verified
Journal Article
Open access
KTKilian Tschoeke
Kilian Tschoeke
IMInka Mueller
Inka Mueller
Vittorio MemmoloVittorio Memmolo
Vittorio Memmolo
MMMaria Moix-Bonet
Maria Moix-Bonet
Jochen MollJochen Moll
Jochen Moll
LSLars Schubert
Lars Schubert
In many industrial sectors, structural health monitoring (SHM) is considered as an addition to nondestructive testing (NDT) that can reduce maintenance effort during the lifetime of a technical facility, structural component, or vehicle. A large number of SHM methods are based on ultrasonic waves, whose properties change depending on structural health. However, the wide application of SHM systems is limited due to the lack of suitable methods to assess their reliability. The evaluation of the system performance usually refers to the determination of the probability of detection (POD) of a test procedure. Up until now, only a few limited methods exist to evaluate the POD of SHM systems, which prevents them from being standardized and widely accepted in the industry. The biggest hurdle concerning the POD calculation is the large number of samples needed. A POD analysis requires data from numerous identical structures with integrated SHM systems. Each structure is then damaged at different locations and with various degrees of severity. All of these are connected to high costs. Therefore, one possible way to tackle this problem is to perform computer-aided investigations. In this work, the POD assessment procedure established in NDT according to the Berens model is adapted to guided wave-based SHM systems. The approach implemented here is based on solely computer-aided investigations. After efficient modeling of wave propagation phenomena across an automotive component made of a carbon-fiber-reinforced composite, the POD curves are extracted. Finally, the novel concept of a POD map is introduced to look into the effect of damage position on system reliability.

23 December 2022 in Sensors
Verified
Journal Article
Open access
PDF file
BKBernd Köhler
Bernd Köhler
LSLars Schubert
Lars Schubert
MBMartin Barth
Martin Barth
KNKazuyuki Nakahata
Kazuyuki Nakahata
Guided elastic wave (GEW) transducers for structural health monitoring (SHM) can act as transmitters (senders) and receivers (sensors). Their performance in both cases depends on the structure to which they are coupled. Therefore, they must be characterized as system transducer- structure. The characterization of the transducer-structure as transmitter using a Scanning Laser Doppler Vibrometer (SLDV) is straightforward, whereas its characterization as receiver is non-trivial. We propose to exploit electromechanical reciprocity, which is an identity between the transfer functions of electrical-to-mechanical and mechanical-to-electrical conversions. For this purpose, the well-known electromechanical reciprocity theorem was adapted to the following situation: The two reciprocal states are “electrical excitation and detection of the surface velocity at point P” and “mechanical excitation at P and measurement of the electrical quantities”. According to the derived formulas, the quantities on the mechanical and electrical sides must be chosen appropriately to ensure reciprocity as well as that the corresponding transfer functions are equal. We demonstrate the reciprocity with experimental data for correctly chosen transfer functions and show the deviation in reciprocity for a different choice. Furthermore, we propose further applications of electromechanical reciprocity.

29 December 2020 in Sensors
Verified
Journal Article
Open access
PDF file
RNRobert Neubeck
Robert Neubeck
MSMareike Stephan
Mareike Stephan
TGTobias Gaul
Tobias Gaul
BWBianca Weihnacht
Bianca Weihnacht
LSLars Schubert
Lars Schubert
JØJan-Magnus Østvik
Jan-Magnus Østvik
The operation efficiency and safety of pressure vessels in the oil and gas industry profits from an accurate knowledge about the inner filling distribution. However, an accurate and reliable estimation of the multi-phase height levels in such objects is a challenging task, especially when considering the high demands in practicability, robustness in harsh environments and safety regulations. Most common systems rely on impractical instrumentation, lack the ability to measure solid phases or require additional safety precautions due to their working principle. In this work, another possibility to determine height levels by attenuation tomography with guided elastic waves is proposed. The method uses a complete instrumentation on the outer vessel shell and is based on the energy conversion rates along the travel path of the guided waves. Noisy data and multiple measurements from sparsely distributed sensor networks are translated into filling levels with accuracies in the centimeter range by solving a constrained optimization problem. It was possible to simultaneously determine sand, water, and oil phases on a mock-up scale experiment, even for artificially created sand slopes. The accuracy was validated by artificial benchmarking for a horizontal vessel, giving references for constructing an affordable prototype system.

30 April 2020 in Aerospace
Verified
Journal Article
Open access
PDF file
KTKilian Tschoeke
Kilian Tschoeke
TGTobias Gaul
Tobias Gaul
APAlexander Pietzsch
Alexander Pietzsch
ESEberhard Schulze
Eberhard Schulze
LSLars Schubert
Lars Schubert
Nowadays, fiber-reinforced plastics are found in numerous industrial applications, such as aerospace, automotive engineering, railway, and naval engineering. These materials have high tensile and flexural strengths and nevertheless a low density at the same time. The use of fiber-reinforced plastics is particularly relevant in areas where large masses have to be moved and accelerated. However, testing and monitoring these structures is still a challenge caused by the different damage behavior compared to metal structures. Non-visible structural changes, such as delaminations and fiber-fractures, may cause local degradation and finally the failure of the components. In this work, active and passive ultrasonic methods based on guided elastic waves are investigated for their applicability to carbon fiber-reinforced structures. Therefore, tensile tests with cyclically increasing load are carried out on specimens with different fiber orientations until complete failure. The acoustic emissions in the specimen during the load are recorded. As a second technique, actively excited guided waves are transmitted and received during the rest periods between the measuring ramps. Different parameters are extracted from the measured data, which allow the monitoring of the specimen’s degradation. A comparison of the results of the active and passive method follows. Finally, a combination of both methods is carried out addressing issues like its informative value and its sensitivity.

1 October 2024 in e-Journal of Nondestructive Testing
Verified
Journal Article
Open access
PDF file
FIFraunhofer Institute for Ceramic Technologies and Systems IKTS
Fraunhofer Institute for Ceramic Technologies and Systems IKTS
LSLars Schubert
Lars Schubert
MSMareike Stephan
Mareike Stephan
ESEberhard Schulze
Eberhard Schulze
APAlexander Pietzsch
Alexander Pietzsch
AMAndré Maun
André Maun
In coal-fired power plants, the flue gas is transported through fibreglassreinforced pipelines to cooling towers during the combustion of the respective raw material, which often serve as a marker for a power plant in the landscape. These glass-fibre reinforced pipelines are located at great heights and can have very large diameters. Up to now, testing has been carried out as part of inspections during planned shutdowns and is associated with corresponding costs. The article discusses the use of acoustic measurement methods based on a 4-month installation at the Niederaußem power plant. Measurement results based on the acoustic emission analysis were shown. For the acoustic emission measurements, a repaired site was instrumented and different parameters like hit/event rates, acoustic energies as well as weighted peak frequencies of the acoustic signals were recorded over the monitoring period of 4 months at power plant Niederaußem. In a second power plant Neurath a 5-month AE monitoring were carried out. This measurement results were discussed as well.

1 August 2026 in e-Journal of Nondestructive Testing
Verified
Journal Article
Open access
PDF file
KTKilian Tschoeke
Kilian Tschoeke
GLGeorg Lautenschläger
Georg Lautenschläger
CKCarsten Kruska
Carsten Kruska
TGTobias Gaul
Tobias Gaul
TKThomas Klesse
Thomas Klesse
MRMike Röllig
Mike Röllig
Hydrogen, as an energy carrier, is finding its way into more and more areas of application, such as on-board tanks for passenger cars, trucks and buses, high-pressure buffer storage at refueling stations, stationary and backup power systems, emerging rail/ship/offshore demonstrators, and industrial/laboratory gas supplies. Safe, available, and cost‑effective hydrogen storage demands monitoring solutions that operate continuously without disrupting service. We present an application‑driven Acousto‑Ultrasonic (AU) concept for Type IV pressure vessels that integrates a dense network of piezoelectric transducers into the outer composite structure via a low‑temperature secondary lamination process. The approach targets guided‑wave interrogation across the cylindrical wall to detect and localize damage relevant to hydrogen service while fitting existing manufacturing and maintenance workflows. A 9 L, 300 bar Type IV vessel (PET liner, carbon fiber overwrap) serves as the demonstrator. The sensing network comprises three circumferential rings of piezoelectric transducers with triangular spacing (typically 3–4 nodes per ring). Signal routing is realized on a thin, conformal multilayer flex PCB that is co‑bonded to the tank and fully encapsulated under glass‑fiber/epoxy cover plies, yielding a total buildup below ~1.5 mm and preserving aerodynamic and handling requirements. The piezoelectric sensors themselves are soldered to the PCB, ensuring a reliable connection. A single external interface—implemented as a low‑profile, keyed, magnetically latched pogo‑pin connector—enables rapid, tool‑less attachment of AU instrumentation while maintaining a sealed, snag‑resistant surface during operation. Process development focused on field viability: vacuum‑assisted hot‑bonding below 90°C avoids thermal over‑exposure of the polymer liner; surface preparation and layup sequences were optimized to minimize voids and ensure adhesion on curved substrates. Trials on representative coupons, metal cylinders, and composite tanks confirmed reliable conformity of 200–350 µm interconnects, robust anchoring of local steel backings for the removable connector, and repeatable lamination with minimal porosity when surfaces are abraded and vacuum levels ~130 mbar are maintained. The measurement concept uses a pitch–catch scheme—one actuator, all others as receivers—with comprehensive shielding and a star‑routed ground to enhance signal integrity over longer runs and reduce the number of required bulkhead connections. The primary impact of this work is twofold. First, it demonstrates a retrofit‑compatible path to deploy guided‑wave SHM on certified vessels without altering the original winding or requiring autoclave processes. Second, it provides a manufacturable blueprint—sensor placement rules, interconnect architecture, connectorization, and a validated lamination window—that scales to larger vessels and higher sensor densities. Ongoing testing includes AU baseline stability under pressure/temperature, defect detectability in the hoop regions, and durability. The results support condition‑based maintenance of hydrogen vessels, enabling reduced inspection downtime, expanded coverage of otherwise inaccessible regions, and improved fleet safety at manageable integration cost.