Heavy metal/ferromagnetic superlattices are of great interest since Néel skyrmions may be stabilized in them due to an interfacial Dzyaloshinskii-Moriya interaction even at room temperature. Here we report on evidence of the strong Dzyaloshinskii-Moriya interaction in symmetric epitaxial superlattices with high perpendicular magnetic anisotropy. The structural and magnetic properties of epitaxial superlattices were investigated dependent on the number of Co/Pd bilayers. Based on comparison of the periodicity of experimentally obtained demagnetized patterns and simulated magnetic structures, a strong increase of the effective Dzyaloshinskii-Moriya interaction constant with increase of the period of superlattices is established. The origin of Dzyaloshinskii-Moriya interaction and its behavior in the symmetric system is discussed.
To stabilize nontrivial spin textures, e.g., skyrmions or chiral domain walls in ultrathin magnetic films, an additional degree of freedom, such as the interfacial Dzyaloshinskii–Moriya interaction (IDMI), must be induced by the strong spin-orbit coupling (SOC) of a stacked heavy metal layer. However, advanced approaches to simultaneously control the IDMI and perpendicular magnetic anisotropy (PMA) are needed for future spin-orbitronic device implementations. Here, we show the effect of atomic-scale surface modulation on the magnetic properties and IDMI in ultrathin films composed of 5d heavy metal/ferromagnet/4d(5d) heavy metal or oxide interfaces, such as Pt/CoFeSiB/Ru, Pt/CoFeSiB/Ta, and Pt/CoFeSiB/MgO. The maximum IDMI value corresponds to the correlated roughness of the bottom and top interfaces of the ferromagnetic layer. The proposed approach for significant enhancement of PMA and the IDMI through interface roughness engineering at the atomic scale offers a powerful tool for the development of spin-orbitronic devices with precise and reliable controllability of their functionality.
Perpendicular magnetic anisotropy in epitaxial trilayered films grown on Si(111) substrate was investigated. Contributions to perpendicular magnetic anisotropy from the bottom and top Co/Pd interfaces were deduced by replacement of Pd layers by Cu layers and comparative analysis of the magnetic anisotropy in the samples. Perpendicular magnetic anisotropy in Pd/Co/Pd films was induced both by interface electronic effects and by stress caused by lattice mismatch between Pd and Co. Due to asymmetry of the stress in the Co film, the contribution to magnetic anisotropy induced by the bottom Co/Pd interface was stronger than that induced by the top Pd/Co interface. The energy of the perpendicular magnetic anisotropy and asymmetrical contributions from the bottom Co/Pd and top Pd/Co interfaces to anisotropy in Pd/Co/Pd trilayers strongly depend on the thickness of the bottom and top Pd layers and may be precisely controlled. The roughness of the interfaces does not have a large influence on the energy of perpendicular magnetic anisotropy in this system.
We investigate the creep of domain walls (DWs) in the combination of in-plane (IP) and out-of-plane magnetic fields in a series of epitaxial Cu(2 nm)/Pd(0–3 nm)/Co(0.7 nm)/Pd(3 nm) samples. Measured velocity curves, , are fitted with an extended dispersive elasticity model, which considers the dependence of both the elastic energy of the DWs and a velocity prefactor in the creep law on the IP magnetic field. The results of the calculations indicate that strong asymmetry in the curves in the investigated system is primarily defined by the dependence of the velocity prefactor on the IP magnetic field, which may be related to a chiral damping effect. The effective energy of the Dzyaloshinskii-Moriya interaction (DMI) increases with increasing thickness of the Pd bottom layer from −0.16 ± 0.03 to . We attribute the complex dependence of the effective DMI energy on the thickness of the Pd bottom layer in the epitaxial Pd/Co/Pd(111) system and the existence of the nonzero DMI in the symmetric Pd(3 nm)/Co(0.7 nm)/Pd(3 nm) samples to unequal strains in the bottom Pd/Co and top Co/Pd interfaces. The elastic strains in the interfaces varying depending on the thickness of the Pd bottom layer strongly influence the magnitude and even the sign of the contributions to the net DMI energy from each interface.
Formation of highly ordered nanostructures on a crystalline silicon surface is highly demanded for novel optoelectronic and nanophotonic designs pushing toward development of inexpensive and high-performing nanostructuring technologies. Here, we demonstrate that laser-induced periodic surface structuring of c-Si protected by a thin Hf over-layer allows one to fabricate extremely uniform high-aspect-ratio gratings with a characteristic periodicity of 900–950 and 450 nm. Corresponding ordering originates from interference of incident IR femtosecond laser pulses with surface plasmons as well as doubling of the grating period via interference of counter-propagating plasmons. A high-melting-point Hf over-layer regulates the c-Si ablation in the plasmon-mediated interference maxima and prevents its excessive oxidation upon multi-pulse exposure in ambient environment. Considering unique high-aspect ratio morphology (a depth-to-period ratio of up to 1.24 and a depth-to-width ratio of up to 8) of the reported nanogratings, their outstanding uniformity, and rather fast printing rate of 0.2 mm2/s as well as possibility for its further upscaling, we envision high practical applicability of this technology in novel optoelectronic devices, visible and near-IR optics, all-dielectric metasurfaces, and sensors.
28 February 2025 in ACS Applied Materials & Interfaces