11 December 2012 in IEEE Transactions on Applied Superconductivity
In recent years, high temperature superconductors (HTSs) have been developed intensively for different applications such as high field magnets, fault current limiters, and current leads. Two-dimensional HTS-based conductors, the coated conductors, used for these applications are multilayered structures on substrate tapes, which can be laminated in addition by a metal, e.g., by copper or stainless steel. Depending on the constituents and the conductor architecture, the thermal conductivity of the whole conductor can vary over several orders of magnitude. Thermal conductivity data are required for calculation of the temperature distribution in a superconducting tape or cable, and for prediction of quench propagation in the conductor itself, and finally in a superconducting device (e.g., coil arrangement). Thermal conductivity data should be measured first of all for the HTS tape, which is used for production of the superconducting appliance. In this paper, we present results of thermal conductivity measurements of the yttrium-barium-copper-oxide copper stabilized superconducting tape in the direction along the tape. Moreover, measurements of the thermal conductivity of the tape in the normal direction are presented.
22 February 2023 in European Journal of Organic Chemistry
A photochemical cyclization of F‐tagged, o ‐alkynylated N ‐alkylamides to indoles catalyzed by [Ir(dF(CF 3 )ppy) 2 (dtbpy)]PF 6 is presented. This straightforward and efficient reaction involves an intramolecular rearrangement due to the presence of an electron withdrawing group in the acyl moiety and is the first example of photochemically induced 1,3‐acyl shift in the cyclization towards 3‐acylindoles. A four‐step reaction sequence including the photoreaction as a key step to the desired indoles has been developed and optimized. The compatibility of differently substituted F‐tagged precursors with the photocyclization step was investigated and the robustness of this step towards modifications could be shown. In total, 16 so far unknown derivatives with diverse modifications in positions N1 and C2, bearing a pentadecafluorooctanoyl moiety as F‐tag, were synthesized in very good yields and fully characterized.
1 July 2022 in Dalton Transactions
Reaction of the ethynyl compound [{HCCC(NDipp)2}2Au2] with n-BuLi followed by Cp2MCl2 (M = Ti, Zr) leads to two group IV – gold(i) heterobimetallic complexes with different photoluminescence properties.
1 January 2012 in AIP Conference Proceedings
For the electrical insulation of superconducting magnets or magnet components, different insulation materials are used that ensure mechanical stability and good electrical insulation properties at low temperatures. Especially glass-fiber-reinforced or sand-filled epoxies are typical material composites that can be used at temperatures down to 4.2 K. For current lead construction within fusion technology, an optimized filled epoxy with respect to mechanical shear strength had to be identified. Therefore different steel/epoxy compositions where examined using the standardized three point bending method. The test specimen were formed putting five layers of glass-fiber lubricated with epoxy between two 1.4429 (316LN) steel frames. The epoxy facing surface of the steel was blasted with glass or corundum. A systematic investigation was performed using different epoxies to get an optimized mechanical performance. The results will be discussed together with data from a sand-filled epoxy compound. For both compounds beside the mechanical properties thermal conductivity and expansion are given in addition.
26 September 2025 in Journal of Materials Chemistry B
Near-infrared (NIR) thermally activated delayed fluorescence (TADF) imaging integrates the benefits of both NIR emission and TADF mechanisms, offering enhanced sensitivity and deeper tissue penetration while enabling time-resolved imaging for biological and medical applications. In this study, we synthesized and studied a donor–acceptor (D–A) type TADF emitter, 7,8-bis(4-(di([1,1'-biphenyl]-4-yl)amino)phenyl)phenazine-2,3-dicarbonitrile (DPPZ), which exhibits strong NIR fluorescence. The photophysical properties of DPPZ were characterized in both toluene and poly(methyl methacrylate) (PMMA) films. In degassed toluene, DPPZ displayed a maximum emission peak at 724 nm with a high photoluminescence quantum yield (ΦPL) of 54.4%, while maintaining a ΦPL of 43.9% in PMMA film under aerated conditions. Upon encapsulation into glassy organic dots (g-Odots), the emitter retained its NIR emission, a ΦPL of 40.1%, and a notably long delayed lifetime (τd) of up to 225.5 μs. These NIR-emissive g-Odots were subsequently applied for lysosome-targeted bioimaging in HeLa cells, demonstrating their potential as effective probes for subcellular imaging.
3 October 2024 in Chemical Communications
The supramolecular host cucurbit[7]uril selectively directs the photolysis of aryl azides to emissive carbolines, highlighting the potential of developing photoactivatable fluorophores using a host–guest strategy.