12 June 2022 in Acta Materialia
7 September 2024 in Ultrasonics
Standard ultrasonic thickness measurements require the sound velocity of the sample to be known and vice versa. We present a method, which we have termed combined mode local acoustic spectroscopy (CoMLAS) for simultaneously determining a plate's thickness and sound velocities without requiring such a priori knowledge. It is based on a combination of three guided wave modes sustained by a plate at discrete frequencies, which we generate and detect using laser ultrasound. We use a pulsed laser that is shaped into a periodic line pattern on the sample's surface to generate elastic waves and measure the response at the pattern's center with a vibrometer. The surface acoustic wave mode produces an interference peak in the response spectrum at the frequency corresponding to the wavelength matching the pattern line spacing. By limiting the total size of the excitation pattern, we can simultaneously generate two zero-group-velocity plate resonances, providing two additional peaks in the spectrum. The plate's local thickness and longitudinal and transverse sound velocities are calculated from the peak frequencies. We demonstrate the feasibility of CoMLAS on steel and aluminum sheets with a thickness of around 2mm by resolving thickness steps and temperature-induced changes in the sound velocities. Using numerical simulations and control experiments, we provide insights into the method's accuracy and limitations. The choice of excitation pattern, the method's sensitivity, and the influence of sample inhomogeneity and anisotropy are discussed. CoMLAS does not require scanning mechanics and provides local plate properties. The results shown are achieved with low-energy lasers and signal averaging. Considerations on signal-to-noise ratio indicate that a realization with available lasers of higher energy will enable single-shot measurements. This qualifies the method for use on moving samples in an industrial environment.
1 March 2020 in Optics & Laser Technology
14 October 2022 in Materialia
20 March 2025 in Journal of Applied Physics
Electroelastic waves in piezoelectric media are widely used in sensing and filtering applications. Despite extensive research, computing the guided wave dispersion remains challenging. This paper presents semi-analytical approaches based on spectral methods to efficiently and reliably compute dispersion curves. We systematically assess the impact of electrical boundary conditions on a 128° Y-cut LiNbO3 wafer, examining open–open, open–shorted, and shorted–shorted surface configurations. Multi-modal dispersion maps obtained from laser-ultrasonic experiments for each boundary condition exhibit excellent agreement with the computational predictions. A straightforward implementation of the spectral collocation method is made available as GEW piezo plate (https://doi.org/10.5281/zenodo.14205789), while the spectral element method is integrated to GEWtool (http://doi.org/10.5281/zenodo.10114243) for multilayered plates. Therewith, we aim to make advanced semi-analytical techniques more accessible to physicists and engineers relying on dispersion analysis.
1 July 2025 in Review of Scientific Instruments
Established techniques for characterizing a layer on a substrate system via surface acoustic wave (SAW) dispersion measurement are often slow due to the need for scanning excitation or detection positions. We present a method for determining discrete points on the SAW mode at equidistant wavenumbers that requires only a single measurement, overcoming these speed limitations. A pulsed laser, shaped into an array of equidistant lines, generates elastic waves on the sample surface. A vibrometer detects the resulting surface displacement next to the line array. The periodic excitation arrangement results in constructive interference of the SAW at wavelengths corresponding to integer fractions of the line spacing. This leads to distinct peaks in the response spectrum, whose higher orders we term spatial harmonics of the SAW. The known line spacing determines the wavelengths, allowing the peak frequencies to be mapped to discrete points on the SAW dispersion curve, effectively sampling the SAW at specific equidistant wavenumbers. By solving an inverse problem, a model can be fit to the experimental data to obtain properties of the layered system. We demonstrate this technique on copper-clad epoxy laminates and roll-cladded aluminum alloy plates and compare our results with dispersion relation scans and micrography. In addition, we analyze the method’s sensitivity to elastic parameters and layer thickness. This approach offers a viable alternative to established SAW scanning methods, particularly in scenarios where the trade-off of lower wavenumber sampling density is acceptable to achieve exceptionally fast measurements while avoiding moving parts.