K. B. Yogesha

K. B. Yogesha

Auto-generated profile, based on publicly available information

K. B. Yogesha

JSS Academy of Technical Education

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
27 November 2019 in Materials Research Express
Verified
Journal Article
Closed access
SMSanthosh Kumar B M
Santhosh Kumar B M
GPGirish D P
Girish D P
YBYogesha K B
Yogesha K B
JCJeevan M C
Jeevan M C

3 July 2019 in Australian Journal of Mechanical Engineering
Verified
Journal Article
Closed access
ARAlam Radhika
Alam Radhika
SAShailesh Rao A
Shailesh Rao A
YBYogesh K B
Yogesh K B
Cutting fluids are generally used for lubrication and cooling the machined surface during the turning operation. The petroleum-based oil, when used for the machining process, has raised many health and environmental issues. The use of bio oils during machining process results in environmental-friendly working atmosphere, with minimal health hazardous among workers. Many researchers have worked on the effect of process parameters, surface characteristics of the machined surface by using bio oils as lubricants. The metallurgical transformation takes place on the machined surface during the machined surface. But the studies on using the bio oils on improving the machined surface, chip formation and generation of cutting force needs to be studied in details with comparison with other process methods. The change in the microstructure, during the machined process also needs to be studied thoroughly, where mere literatures are available. With this direction, the experimental studies were conducted to study the machining parameters during the turning process by using gingelly oil as cutting fluids. The studies showed that there was a gradual decrease in cutting force and improved surface finish on the machined part. The improvement in the machinability during the cutting process with respect to chip length, pitch and surface roughness was discussed for all the process. Finally, the changes in the microstructure on the metal surface for the different cutting forces were studied.

14 June 2019
Verified
Book Chapter
Closed access
PDF file
PSPappur Nagappa Shivakumar
Pappur Nagappa Shivakumar
MHM. B. Hanamantraygouda
M. B. Hanamantraygouda
LPL. Prashanth
L. Prashanth
KYK. B. Yogesha
K. B. Yogesha
PSP. Siddappa
P. Siddappa
MMM. Mrityunjaya
M. Mrityunjaya

14 October 2020
Verified
Book Chapter
Open access
PDF file
MPM. Prajwal
M. Prajwal
KYK. B. Yogesha
K. B. Yogesha
KUKalmeshwar Ullegaddi
Kalmeshwar Ullegaddi
KKK. G. Basava Kumar
K. G. Basava Kumar
Fracture analysis of crack growth in between two material interfaces (different engineering materials) is one of the challenging tasks in the engineering field. In the present investigation, different properties of bi-material are considering to study the damage-tolerant design and analysis of fracture mechanics. A double cantilever beam (DCB) with a bi-material crack is considered for analysis. In FEM, specifically a post-processing command virtual crack closure technique (VCCT) is used for evaluation of mixed mode energy release rate of bi-material interface cracks. Validation of obtained results is done with a benchmark problem in the literature. Then parametric studies have been conducted on four different material combinations for a range of crack length and height of the beam. The results generated will be useful for assessing structural integrity.

9 January 2018 in MATEC Web of Conferences
Verified
Journal Article
Open access
PSP. N. Siddappa
P. N. Siddappa
BSB. P. Shivakumar
B. P. Shivakumar
KYK. B. Yogesha
K. B. Yogesha
MMM. Mruthunjaya
M. Mruthunjaya
MHM. B. Hanamantraygouda
M. B. Hanamantraygouda
Aluminum Metal Matrix Composites have emerged as an advanced class of structural materials have a combination of different, superior properties compared to an unreinforced matrix, which can result in a number of service benefits such as increased strength, higher elastic moduli, higher service temperature, low CTE, improved wear resistance, high toughness, etc. The excellent mechanical properties of these materials together with weight saving makes them very attractive for a variety of engineering applications in aerospace, automotive, electronic industries, etc. Hence, these materials provide as alternative substitutes for conventional engineering materials when specific mechanical properties necessary for required applications. In this work an attempt is made to study the machining parameters of Al6061/TiC MMC. The composite is developed by reinforcing TiC particles in varying proportions of 3, 6, 9 and 12 % weight fractions to the Al6061 matric alloy through stir casting technique. Cutting forces were measured by varying cutting speed and feed rate with constant depth of cut for different % weight fractions. The results showed that the cutting force increases with the increase of feed rate and decreases with the increase of cutting speed for all the weight fractions. Cutting parameters were optimized using Taguchi technique.