Jane O'DEll

Jane O'DEll

Auto-generated profile, based on publicly available information

Jane O'DEll

Forest Products Laboratory, Madison, USA

Research Focus & Metrics

Academic Career Length

20Years (2007-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 May 2008 in Biotechnology Progress
Verified
Journal Article
Closed access
PDF file
ELEdwin N. Lightfoot
Edwin N. Lightfoot
TRThatcher W. Root
Thatcher W. Root
JOJane L. O'DEll
Jane L. O'DEll
An algorithm is developed for describing ideal membrane cascades for fractionation of binary and pseudo‐binary mixtures. It is shown that solvent management plays a key role in determining both purification and yield. Development of efficient diafilters is needed if membrane cascades are to achieve their full potential in competing with both chromatography and simulated moving bed operations in downstream processing of proteins. Such a replacement will also be important for fractionation of higher titers and larger substrates, such as plasmids, viruses, and even whole cells.

19 December 2023 in Food Hydrocolloids
Verified
Journal Article
Closed access
JGJing Geng
Jing Geng
JOJane O'DEll
Jane O'DEll
NIcole StarkNIcole Stark
NIcole Stark
PKPeter Borissov Kitin
Peter Borissov Kitin
XZXiao Zhang
Xiao Zhang
JZJunyong Zhu
Junyong Zhu

1 July 2007 in Separation Science and Technology
Verified
Journal Article
Closed access
SGS. S. Gunderson
S. S. Gunderson
WBW. S. Brower
W. S. Brower
JOJ. L. O'DEll
J. L. O'DEll
ELE. N. Lightfoot
E. N. Lightfoot
Suggestions are made for the practical implementation of membrane cascades using diafiltration for the fractionation of solute pairs. Experiments are described that demonstrate the desirability of replacing solvent during the course of each diafiltration, and a parallel modeling development suggests an attractive means for accomplishing this replacement. A batch process is described to achieve such separations by simple assemblies of existing equipment, and suggestions are made for designing continuous processors. Such cascades are attractive for a wide variety of solutes including native proteins, as well as commodity chemicals, and they can be applied to the resolution of enantiomers through simple modifications already described in the public literature. The same techniques can be applied to multicomponent systems using the concept of key components as has long been done in distillation. The low inherent capital costs and high throughput rates of such membrane cascades strongly suggest that they should compete successfully against a significant number of presently used chromatographic processes, and their simplicity should make then formidable competitors to simulated moving beds as well.

28 November 2020 in European Journal of Wood and Wood Products
Verified
Journal Article
Open access
PDF file
Andreja KutnarAndreja Kutnar
Andreja Kutnar
JOJane O’dEll
Jane O’dEll
CHChristopher Hunt
Christopher Hunt
CFCharles Frihart
Charles Frihart
FKFred Kamke
Fred Kamke
MSMatthew Schwarzkopf
Matthew Schwarzkopf
Thermo-hydro-mechanical (THM) processing can improve the intrinsic properties of wood, produce new materials, and give desired form and function to new applications. THM treatments change the mechanical properties of wood and may change its viscoelastic properties as well. Therefore, the objective of this study was to assess the viscoelastic properties of THM-treated wood at several humidity and load levels. To explore these changes, this study applied a THM treatment to beech (Fagus sylvatica L.) wood with steam (620 kPa) and heat (170 °C), followed by densification and increased temperature (200 °C) in a hot-press, which was then cooled while under pressure. Two initial specimen thicknesses before THM treatment were used to study the difference between density ratios. Specimens were tested in a humidity-controlled dynamic mechanical analyser (DMA) to apply creep stress with different loading levels (20% and 30% of expected modulus of rupture) and relative humidity levels (30%, 50%, and 65% RH). The creep compliance/recovery response was monitored, and dynamic moduli were measured before and after the application of creep stress. The loss modulus measured was highest for specimens tested at 65% RH and lowest in specimens tested at 30% RH, which is a direct result of the viscous response of the material. Increased damping of the specimens was also observed at higher RH, which is typical for wood products due to added moisture in the cell wall acting as a plasticizer to cell wall polymers. Like previous studies, THM treatment lowered the equilibrium moisture content (EMC) of densified wood specimens, which affected their mechanical performance. THM treatment yields higher strength and lower EMC, suggesting that this product could be suitable for structural applications where their service life is in an indoor environment. THM treatment also resulted in decreased creep compliance and recovery compliance as compared to control specimens.

1 July 2008 in Holzforschung
Verified
Journal Article
Closed access
JHJohn F. Hunt
John F. Hunt
JOJane O'Dell
Jane O'Dell
CTChris Turk
Chris Turk
Fibers from treetop residues of lodgepole pine (Pinus contorta) and recycled old corrugated containers were used to fabricate wet-formed fiberboard panels over a range of densities from 300 to 1100 kg m-3, a thickness range from 1.3 to 4.8 mm, and phenolic resin contents from 0% to 4.5%. The panels were then tested after conditioning in 50% and 90% relative humidity (RH) environments. Density, thickness, equilibrium moisture content, bending modulus of elasticity (MOE), and modulus of rupture (MOR) were measured for each panel. Panel apparent-density increased with thickness, but this may be due to surface effects rather than true density values. The equilibrium moisture content approximately doubled for the panels in the 90% RH environment, compared to 50% RH. At 50% and 90% RH conditions, equilibrium moisture contents decreased significantly when only 0.5% resin was added and remained essentially the same with increasing resin levels. In this study, both MOE and MOR increased with approximately the square of density. MOE increased, whereas MOR showed no clear effects as thickness and resin amount increased. This research is part of a larger program for developing an understanding of panel properties for engineered three-dimensional fiberboard products.

1 March 2015 in Forest Products Journal
Verified
Journal Article
Closed access
CHChristopher Hunt
Christopher Hunt
JOJane O'DEll
Jane O'DEll
Joseph JakesJoseph Jakes
Joseph Jakes
WGWarren J. Grigsby
Warren J. Grigsby
CFCharles R. Frihart
Charles R. Frihart
Although it is well known that wood can absorb liquids, the full impact of this phenomenon on resulting adhesive cure and performance is not well understood. In a related soy adhesive study, aspects of this phenomenon were not fully anticipated and resulted in a significant impact on adhesive bond quality. In essence, the wood being bonded acted like chromatography media, filtering relatively smaller molecules from the surrounding adhesive matrix and altering the local composition of the adhesive material. Through the use of soy adhesives containing glycerin, the infiltration of glycerin analogs into wood cell walls has been determined and related with the impact on bondline and wood properties. The impacts of infiltration and chromatographic separation on the cured adhesive are also discussed.