4 April 2025 in IEEE Transactions on Biomedical Circuits and Systems
This article presents a direct-digitization analog front end (DD-AFE) with enhanced input-impedance, common-mode rejection ratio (CMRR), and dynamic range (DR) for wearable biopotential (ExG) signal acquisition, especially for small-diameter dry electrodes. The DD-AFE employs a second-order continuous-time delta-sigma modulator (CT-ΔSM) and multiple circuit techniques to support direct-digitization readouts. These include 1) A high input-impedance input feedforward (FF), embedded in a 4-input 4-bit successive approximation register (SAR) quantizer. This allows two integrators to adopt a compact and energy-efficient Gm-C structure, and improves stability and linearity, resulting in a 6.6dB increase in DR, 42dB increase in SQNR at peak input and a unity-gain signal transfer function (STF) with a gain flatness of 0.04%. 2) A fixed-voltage dead-band assisted tri-level current-steering DAC (IDAC). It not only increases the DR and CMRR of the DD-AFE but also eliminates the harmonic distortion induced by tri-level dynamic element matching (DEM). 3) A high-gain two-stage Gm-boosting inverter-based OTA with embedded low-frequency chopping. The former largely improves linearity and CMRR, while the latter mitigates 1/f noise without compromising the input impedance. Fabricated in a 0.18-μm CMOS process, this DD-AFE achieves 6.4GΩ input impedance and 104.5dB CMRR at 50Hz, as well as 90.4dB peak SNDR, 96dB DR, and up to 425mVPP linear input range.
12 November 2025 in IEEE Journal of Solid-State Circuits
A 14-cell monitoring analog front-end (AFE) is presented for comprehensive battery pack diagnostics and control, aiming to enhance performance and extend lifespan. The AFE measures each cell’s DC voltage and electrochemical impedance spectroscopy (EIS), supporting accurate estimation of the state of charge (SOC) and state of health (SOH) of lithium battery packs. By integrating dynamic circuit techniques with a hardware-reuse strategy at both the system and circuit levels, the design achieves high measurement resolution, compact area, and improved energy efficiency. The capacitively coupled instrumentation amplifier (CCIA) measures DC voltage under high-voltage (HV) common-mode conditions and is subsequently repurposed for intermittent EIS acquisition. An interchannel auto-zeroing stabilization (AZS) scheme time-interleaves ripple suppression across multiple chopper-stabilized CCIAs, enhancing voltage resolution without additional area. Furthermore, synchronizing the incremental delta-sigma modulator (IDSM) decimation filter with the chopping clock and adjusting filter weights provides additional ripple suppression without extra circuitry. The built-in EIS function leverages the passive balancing circuit to perform fast, broadband impedance measurement using a 1-bit delta-sigma-modulated excitation current. Fabricated in a 0.18- $\mu $ m BCD process, the 14-cell AFE core operates from a 5-V supply, consumes 11.5 mW, and achieves a post-calibration maximum DC total measurement error (TME) of 1 mV from ${-} 40~{^{\circ }}$ C to $85~{^{\circ }}$ C. The EIS attains 0.2-m $\Omega $ sensitivity and 2-kHz bandwidth.
1 January 2026 in IEEE Journal of Solid-State Circuits
31 October 2025 in IEEE Journal of Solid-State Circuits
This article presents a high-linearity, robust-jitter tolerance digital-to-analog converter (DAC) for high-fidelity audio systems. To improve the linearity, we propose a compact digital shaper utilizing a single vector quantizer (VQ) to mitigate both DAC mismatch and inter-symbol interference (ISI) with low system complexity. Two dummy current-steering DAC (IDAC) units are incorporated to further enhance linearity at high input levels. In addition, noise-shaped segmentation is used in the shaper and IDAC, which reduces hardware complexity and retains high signal-to-noise ratio (SNR) and linearity. Finally, the third-order digital delta–sigma modulator (DSM) has its coefficients optimized to improve IDAC jitter tolerance. Fabricated in a 0.18- $\mu $ m CMOS technology, this audio DAC achieves a state-of-the-art total harmonic distortion (THD) of −117.1 dB at −2.1 dBFS. By adopting resistive degeneration, optimized biasing current, and RC filter in the IDAC unit, this work exhibits a THD plus noise (THD + N) of −107.4 dB and an A-weighted dynamic range (DR) of 111.2 dB. Thanks to the optimized digital DSM, even under a 620-ps rms clock jitter, this DAC attains an excellent THD + N of −100.9 dB.