12 February 2015 in IEEE Transactions on Energy Conversion
This paper presents the conceptual analysis, comparative simulation, and experimental evaluation of voltage and flux vector-oriented control of a promising low-cost brushless doubly-fed reluctance generator (BDFRG) technology for variable-speed wind turbines with maximum power point tracking. The BDFRG has been receiving increasing attention because of the use of partially rated power electronics and the high reliability of brushless design, while offering performance competitive to its popular slip-ring counterpart, the doubly-fed induction generator. The development and viability of the two parameter-independent controllers have been validated on a custom-made BDFRG prototype using the maximum torque per inverter ampere strategy for the speed and loading conditions commonly encountered in wind power applications.
1 February 2020 in IOP Conference Series: Materials Science and Engineering
BLDC motor has many applications in high power systems. Whereas, it is easy to construct and design, cheap and needs less maintenance, with high efficiency, high output power, and high torque. By taking advantage of power electronics drives, a rectifier/multi-level inverter can improve the operation of BLDC motor in medium and high applications. In this research, a mathematical model of BLDC motor drive by rectifier/MLI has been simulated using Matlab/Simulink. Whereas, a proposed model system was built, with a two-part motor drive circuits: a three-phase full-wave fully controlled rectifier, and a three-level inverter. The pulses circuit is designed for rectifier and three-level inverter individually using PWM. Also, THD in the output of a three-level inverter has been reduced by using a modern SFO-PWM topology. In addition, the system is equipped with a PI controller to control the speed and torque of BLDC motor. Also, there is a high-quality control upon the speed and torque of the motor due to the use of PI controller, which resulted in constant torque with low ripple and constant speed as a load of the motor changed, with a high increasing in the stability and reliability of the system.
1 August 2023 in Indonesian Journal of Electrical Engineering and Computer Science
Switched reluctance motors (SRM) becomes increasingly popular due to its simple structure and dependability. It seems to have a two-pole configuration. A stator had also centralized coils along each pole, whereas a rotor has an iron core only. As a result, the switched reluctance motor is anticipated to be a low cost, incredibly robust variable-speed machine. Because the switched reluctance motor is only made up of laminated coils, its performance is heavily reliant on the magnetic properties of the core material. Vibration, torque ripple, and low torque for each unit volume are some of their drawbacks. Typically, a standard proportional-integral-derivative (PID) controller is designed to regulate the Switched Reluctance Motor's speed. Furthermore, the PID controller could also regulate and control SRM when the load changes abruptly. A fuzzy logic controller (FLC) is utilized within this article to regulate the speed of the SRM drive. The MATLAB/Simulink platform is used to analyze the behavior of SRM with FLC. To demonstrate FLC's superiority, its results have been compared to that of a typical PID controller.
1 April 2018 in International Journal of Electrical and Computer Engineering (IJECE)
This paper describes the importance of FACTS devices; it presents the outcome of the study of its reflectance on the performance of power system networks. It seeks to increase and guarantee the fact and accuracy of response systems under disturbance conditions when the phase measurement units are introduced as Real-Time Measurement (RTM) stations. This paper also describes the importance of FACTS devices. The combination of FACTS devices and PMUs is presented to increase the controllability performance of power systems. This paper demonstrates how PMUs measure voltage, current and their angles. It provides, through a communication link, a Phase Angle Data Concentrator (PDC) to make an appropriate decision to correct the power system state using the FACTS device (TCSC). We utilized the Graph-Theoretic Algorithm to optimize the number and location of PMUs. The technique proposed was tested on the Iraqi National Super Grid’s 24bus network, Diyala City’s regional 10bus network and the 14bus IEEE standard test system. The MATLAB/PSAT package was utilized for the simulation of results. It is evident that our proposed algorithm and technique achieved the purpose of this paper as confirmed by the level of accuracy of the results obtained from most of the cases tested.