Peter R. Kinget

Peter R. Kinget

Auto-generated profile, based on publicly available information

Peter R. Kinget

Department of Electrical Engineering, Columbia University, New York, NY, USA

Research Focus & Metrics

Academic Career Length

36Years (1991-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
5 December 2005 in IEEE Journal of Solid-State Circuits
Verified
Journal Article
Closed access
SCS. Chatterjee
S. Chatterjee
YTY. Tsividis
Y. Tsividis
PKP. Kinget
P. Kinget
We present design techniques that make possible the operation of analog circuits with very low supply voltages, down to 0.5 V. We use operational transconductance amplifier (OTA) and filter design as a vehicle to introduce these techniques. Two OTAs, one with body inputs and the other with gate inputs, are designed. Biasing strategies to maintain common-mode voltages and attain maximum signal swing over process, voltage, and temperature are proposed. Prototype chips were fabricated in a 0.18-/spl mu/m CMOS process using standard 0.5-V V/sub T/ devices. The body-input OTA has a measured 52-dB DC gain, a 2.5-MHz gain-bandwidth, and consumes 110 /spl mu/W. The gate-input OTA has a measured 62-dB DC gain (with automatic gain-enhancement), a 10-MHz gain-bandwidth, and consumes 75 /spl mu/W. Design techniques for active-RC filters are also presented. Weak-inversion MOS varactors are proposed and modeled. These are used along with 0.5-V gate-input OTAs to design a fully integrated, 135-kHz fifth-order elliptic low-pass filter. The prototype chip in a 0.18-/spl mu/m CMOS process with V/sub T/ of 0.5-V also includes an on-chip phase-locked loop for tuning. The 1-mm/sup 2/ chip has a measured dynamic range of 57 dB and draws 2.2 mA from the 0.5-V supply.

13 June 2005 in IEEE Journal of Solid-State Circuits
Verified
Journal Article
Closed access
PKP.R. Kinget
P.R. Kinget
Random device mismatch plays an important role in the design of accurate analog circuits. Models for the matching of MOS and bipolar devices from open literature show that matching improves with increasing device area. As a result, accuracy requirements impose a minimal device area and this paper explores the impact of this constraint on the performance of general analog circuits. It results in a fixed bandwidth-accuracy-power tradeoff which is set by technology constants. This tradeoff is independent of bias point for bipolar circuits whereas for MOS circuits some bias point optimizations are possible. The performance limitations imposed by matching are compared to the limits imposed by thermal noise. For MOS circuits the power constraints due to matching are several orders of magnitude higher than for thermal noise. For the bipolar case the constraints due to noise and matching are of comparable order of magnitude. The impact of technology scaling on the conclusions of this work are briefly explored.

1 January 1999
Verified
Book Chapter
Closed access
PDF file
PKPeter Kinget
Peter Kinget

12 August 2011 in IEEE Journal of Solid-State Circuits
Verified
Journal Article
Closed access
MCMarco Crepaldi
Marco Crepaldi
CLChen Li
Chen Li
JFJorge Fernandes
Jorge Fernandes
PKPeter R. Kinget
Peter R. Kinget
This work presents a low-complexity IR-UWB chipset which achieves synchronization and demodulation at the receiver relying only on a ring oscillator clock. The modulation scheme used, synchronized-OOK (S-OOK), permits low power timing acquisition and data reception with a static CMOS digital synchronizer and demodulator counting 61 logic elements. The receiver consists of a modified energy detector (ED) that allows to asynchronously receive UWB pulses in presence of narrowband interference (NBI) with power levels up to -5 and -16 dBm for 5.4 and 2.4 GHz continuous wave interfering signals respectively. The sensitivity is -60/ -66 dBm with an overall energy dissipation of 2.9/3.9 nJ/bit for a 1 Mbps S-OOK PRBS data stream and a 100% power duty cycle. The complete demodulation and synchronization digital back-end consumes only 0.2 mW (including on-chip output buffers) during normal operation. The IR-UWB transmitter is based on a gated LC oscillator and achieves pulse durations of ~2 ns for bandwidths of 500 MHz. It consumes 249 pJ/bit energy per bit at 1 Mbps OOK.

22 February 2010 in IEEE Journal of Solid-State Circuits
Verified
Journal Article
Closed access
ABAjay Balankutty
Ajay Balankutty
SYShih-An Yu
Shih-An Yu
YFYiping Feng
Yiping Feng
PKPeter R. Kinget
Peter R. Kinget
Supply voltage reduction with process scaling has made the design of analog, RF and mixed mode circuits increasingly difficult. In this paper, we present the design of an ultra-low voltage, low power and highly integrated dual-mode receiver for 2.4-GHz ISM-band applications. The receiver operates reliably from 0.55-0.65 V and is compatible with commercial standards such as Bluetooth and ZigBee. We discuss the design challenges at low voltage supplies such as limited fT for transistors and higher nonlinearities due to limited available signal swing, and present the architectural and circuit level design techniques used to overcome these challenges. The highly integrated receiver prototype chip contains RF front-end circuits, analog baseband circuits and the RF frequency synthesizer and was fabricated in a standard digital 90-nm CMOS process; it achieves a gain of 67 dB, noise figure of 16 dB, IIP3 of -10.5 dBm, synthesizer phase noise of - 127 dBc/Hz at 3-MHz offset, consumes 32.5 mW from 0.6 V and occupies an active area of 1.7 mm2.

26 February 2007 in IEEE Journal of Solid-State Circuits
Verified
Journal Article
Closed access
KPKong-Pang Pun
Kong-Pang Pun
SCShouri Chatterjee
Shouri Chatterjee
PKPeter R. Kinget
Peter R. Kinget
A 0.5-V third-order one-bit fully-differential continuous-time DeltaSigma modulator is presented. The presented modulator architecture uses true low-voltage design techniques, and does not require internal voltage boosting or low-threshold devices. A return-to-open architecture that enables the ultra-low-voltage realization of return-to-zero signaling for the feedback DAC is proposed. The ultra-low-voltage operation is further enabled by a body-input gate-clocked comparator, and body-input operational transconductance amplifiers for the active-RC loop filter. Fabricated on a 0.18-mum CMOS process, the modulator achieves a peak SNDR of 74 dB in a 25 kHz bandwidth, and occupies an area of 0.6 mm2; the modulator core consumes 300 muW.