Evgeniy V. Safonov

Evgeniy V. Safonov

Auto-generated profile, based on publicly available information

Evgeniy V. Safonov

South Ural State University

Research Focus & Metrics

Academic Career Length

14Years (2013-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 February 2016 in Materials Science Forum
Verified
Journal Article
Closed access
PDF file
PLPavel Lykov
Pavel Lykov
ESE.V. Safonov
E.V. Safonov
AAA.M. Akhmedianov
A.M. Akhmedianov
In this work the selective laser melting (SLM) of pure copper powder was studied. Because of low laser radiation absorption and high thermal conductivity it is very difficult to organize stable SLM process for copper. Five 10x10x5 mm specimens were fabricated by using different process parameters (scanning speed, point distance, exposure time, scanning strategy). The structure of fabricated specimens was studied by scanning electron microscopy of polished cross-sections. The tensile test was carried out for SLM regime with the lowest porosity.

5 April 2016 in SAE International Journal of Advances and Current Practices in Mobility
Verified
Conference Paper
Closed access
PLPavel Lykov
Pavel Lykov
RBRustam Baytimerov
Rustam Baytimerov
SVSergey Vaulin
Sergey Vaulin
ESEvgeny Safonov
Evgeny Safonov
DZDmitry Zherebtsov
Dmitry Zherebtsov
Due to its unique physical properties (high thermal and electric conductivity) copper is one of the most interesting materials in point of view of additive manufacturing in particular of Selective Laser Melting (SLM). But because of the low laser radiation absorption, low melting point and high thermal conductivity it is difficult to fabricate of copper components without pores. Results of many research have been shown that for successful Selective Laser Melting of copper powder is needed high laser power (more than 300 W) and high laser scanning speed (more than 600 mm/s). However now most SLM machines are equipped with laser plants with output power up to 200 W.In this research, SLM machine with 200 W maximum power CO2 laser has been used. For determination of the influence of SLM process parameters on quality of copper parts cubic specimens have been fabricated. The point distance, exposure time and base plate preheating temperature have been changing. For fabricated specimens porosity by scanning electron microscopy have been determined.

20 October 2017 in IOP Conference Series: Materials Science and Engineering
Verified
Conference Paper
Open access
PDF file
RBRustam Baitimerov
Rustam Baitimerov
PLPavel Lykov
Pavel Lykov
Radionova LiudmilaRadionova Liudmila
Radionova Liudmila
ESE V Safonov
E V Safonov
TiAl6V4 alloy is one of the widely used materials in powder bed fusion additive manufacturing technologies. In recent years selective laser melting (SLM) of TiAl6V4 alloy by fiber laser has been well studied, but SLM by CO2-lasers has not. SLM of TiAl6V4 powder by CO2-laser was studied in this paper. Nine 10×10×10 mm cubic specimens were fabricated using different SLM process parameters. All of the fabricated specimens have a good dense structure and a good surface finish quality without dimensional distortion. The lowest porosity that was achieved was about 0.5%.

31 July 2013 in Metallurgist
Verified
Journal Article
Closed access
PDF file
PLPavel Lykov
Pavel Lykov
ESE. V. Safonov
E. V. Safonov
ASA. O. Shul’ts
A. O. Shul’ts

1 January 2016 in Procedia Engineering
Verified
Journal Article
Open access
AKA.L. Kartashev
A.L. Kartashev
MKM.A. Kartasheva
M.A. Kartasheva
ESE.V. Safonov
E.V. Safonov
In this paper, application of the Ranque-Hilsh vortex effect for creation of the evaporation plant for water demineralization is considered. The Ranque-Hilsch effect in a vortex flow is researched. The device used for application of this effect – the evaporation plant - is presented. Problems of the eddy currents modelling in the evaporation plant for water demineralization with a phase transfer implementing the Ranque-Hilsch effect are described

1 January 2017 in Bulletin of the South Ural State University Series "Mechanical Engineering Industry"
Verified
Journal Article
Open access
PDF file
RBRustam Baitimerov
Rustam Baitimerov
PLPavel Lykov
Pavel Lykov
Radionova LiudmilaRadionova Liudmila
Radionova Liudmila
ЕСЕвгений Владимирович Сафонов
Евгений Владимирович Сафонов
Один из наиболее часто применяемых сплавов в аддитивных технологиях – титановый сплав TiAl6V4. В последние годы большое количество работ посвящалось исследованию селективного лазерного сплавления данного сплава при использовании оптоволоконного лазера. В данной работе исследовались режимы SLM с применением углекислотного лазера. Для исследования влияния параметров селективного лазерного сплавления на пористость получаемого материала использовалась установка SINTERSTATION® Pro DM125 SLM System. Образцы выращивались в инертной атмосфере (содержание кислорода в рабочей камере составляло 500 ppm). В работе использовался порошок титанового сплава с размером частиц от 20 мкм до 63 мкм, средним размером частиц – 44 мкм, средней сферичностью по параметру ISO Roundness – 63,74 %. С использованием девяти различных режимов сплавления были изготовлены образцы кубической формы. Пористость определялась методом исследования шлифа на оптическом микроскопе (изготавливались 2 шлифа: совпадающий с направлением выращивания образца и перпендикулярный направлению выращивания). Все полученные образцы имеют плотную структуру и удовлетворительное качество поверхности. Наибольшую пористость (22,6 %) имеет образец, для сплавления которого использовалась мощность лазера – 100 Вт, время выдержки лазера в координате – 50 мкс (поры в данном случае имеют неправильную форму и большой размер). Наименьшую пористость (0,5 %) имеет образец, для сплавления которого использовалась мощность лазера – 200 Вт, время выдержки лазера в координате – 150 мкс (поры в данном случае имеют сферическую форму и меньшие размеры).