Rabindra Kishore Mishra

Rabindra Kishore Mishra

Auto-generated profile, based on publicly available information

Rabindra Kishore Mishra

Electronic Science and Technology, Berhampur University, Berhampur, Odisha, India

Research Focus & Metrics

Academic Career Length

25Years (2002-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
5 April 2011 in IEEE Microwave and Wireless Components Letters
Verified
Journal Article
Closed access
RGRowdra Ghatak
Rowdra Ghatak
PSPankaj Sarkar
Pankaj Sarkar
RMR. K. Mishra
R. K. Mishra
DPD. R. Poddar
D. R. Poddar
In this letter, an ultrawideband (UWB) bandpass filter with a band notch is proposed. The UWB BPF (3.1-10.6 GHz) is realized by cascading a distributed high-pass filter and an elliptic low-pass filter with an embedded stepped impedance resonator (SIR) to achieve a band notch characteristic. The notch band is obtained at 5.22 GHz. It is shown that the notch frequency can be tuned by changing the impedance ratio of the embedded SIR. A fabricated prototype of the proposed UWB bandpass filter is developed. The inband and out-of-band performance obtained by measurement, EM simulation, and that with an equivalent circuit model are in good agreement.

3 November 2022 in IEEE Antennas and Wireless Propagation Letters
Verified
Journal Article
Closed access
DNDeepak Kumar Naik
Deepak Kumar Naik
RSRajanikanta Swain
Rajanikanta Swain
DPDhruba Charan Panda
Dhruba Charan Panda
RMRabindra Kishore Mishra
Rabindra Kishore Mishra
This paper presents a design approach for a defected ground structure (DGS) based wideband circular microstrip patch antenna using the characteristic mode analysis (CMA). It emphasizes improving two design aspects: cross-polarization reduction and bandwidth enhancement. The CMA unveils the intrinsic characteristic modes in the patch and ground plane, and then undesired modes are suppressed using a DGS, reducing cross-polarized radiations. Another defect, strategically incorporated into the same DGS, enhances a higher-order non-radiating mode to radiate and increases bandwidth. The proposed design fabricated on an FR-4 substrate achieves a $\simeq$ 16% impedance bandwidth (5.7–6.7 GHz) with dimensions $0.8\lambda _{0}\times 0.8\lambda _{0}\times 0.03\lambda _{0}$ ( $\lambda _{0}$ being the free-space wavelength at 6 GHz) and 10–15 dB average cross-polarization reduction at $\pm$ 60° angle of boresight. The measured results from a fabricated prototype agree well with the proposed design.

9 March 2020 in Journal of Electrical Engineering & Technology
Verified
Journal Article
Closed access
PDF file
RSRajanikanta Swain
Rajanikanta Swain
ACAyan Chatterjee
Ayan Chatterjee
SNSambhudutta Nanda
Sambhudutta Nanda
RMRabindra Kishore Mishra
Rabindra Kishore Mishra

6 July 2022 in AEU - International Journal of Electronics and Communications
Verified
Journal Article
Closed access
DNDeepak K. Naik
Deepak K. Naik
ASAmit K. Sahu
Amit K. Sahu
RPRajeev K. Parida
Rajeev K. Parida
PRP. Raiguru
P. Raiguru
DPDhruba Charan Panda
Dhruba Charan Panda
RMRabindra K. Mishra
Rabindra K. Mishra

24 February 2012 in International Journal of RF and Microwave Computer-Aided Engineering
Verified
Journal Article
Closed access
PDF file
RGRowdra Ghatak
Rowdra Ghatak
DSDipali Soren
Dipali Soren
RMRabindra Kishore Mishra
Rabindra Kishore Mishra
DPDipak Ranjan Poddar
Dipak Ranjan Poddar
In this article, a modified fractal rectangular curve (FRC)-shaped dielectric resonator antennas (DRA) with two different functionalities is reported. These antennas are split in the middle into two halves and are excited by a coaxial probe. In first configuration, the fractal geometry is used to achieve wide bandwidth from 3.5 to 5.0 GHz covering the body area network frequencies as well as the IEEE 802.11a WLAN frequencies. The average peak gain within the band is about 7 dBi. The second investigation involves miniaturization of rectangular DRA by using FRC along the cross-sectional boundary. By this, a DRA at 3.2 GHz could be realized using second iteration of modified rectangular curve fractal geometry resulting in a 50% size reduction by maintaining same radiation characteristics. © 2012 Wiley Periodicals, Inc. Int J RF and Microwave CAE, 2012.

1 July 2024 in IEEE Antennas and Wireless Propagation Letters
Verified
Journal Article
Closed access
AGAkhila Gouda
Akhila Gouda
RMRabindra Kishore Mishra
Rabindra Kishore Mishra
SGSaptarshi Ghosh
Saptarshi Ghosh
This letter presents an innovative mapping technique to design and demonstrate a frequency selective surface (FSS) based bandstop filter on a sinusoidal surface. The novelty of the method lies in the uniform placement of the unit cells on different non-planar surfaces using a hybrid method comprising an analytical technique and full-wave simulation that significantly improves the shielding characteristic in a wideband spectrum (having a -10 dB stopband from 7 to 13 GHz with a fractional bandwidth of 60%). A conventional metallic square loop is considered as the constituent unit cell topology, which is intelligibly positioned over a large surface using the proposed method. The structure is then simulated using the finite element boundary integral, as well as fabricated exploiting the threedimensional (3-D) printing technology, thereby validating the proposed concept. Such non-planar FSS geometries have potential in diverse applications, including shielding and aerospace sectors.