Kacper Skarżyński

Kacper Skarżyński

Auto-generated profile, based on publicly available information

Kacper Skarżyński

Micro- and Nanotechnology Division, Institute of Metrology and Biomedical Engineering, Faculty of Mechatronics, Warsaw University of Technology, Warsaw, Poland

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
13 September 2021 in Scientific Reports
Verified
Journal Article
Open access
PDF file
KSKacper Skarżyński
Kacper Skarżyński
JKJakub Krzemiński
Jakub Krzemiński
Małgorzata JakubowskaMałgorzata Jakubowska
Małgorzata Jakubowska
MSMarcin Sloma
Marcin Sloma
Recently, low-cost electronics printed on lightweight, flexible and 3D shaped substrates are gaining importance in the markets of wearables and smart packaging. However, printed electronics do not meet the electrical performance of subtractive techniques because the resistivity of metallic printed patterns is still much higher than that of bulk material. To fulfil this need, low-resistive and easy printable inks for high resolution printed electronics techniques are needed. In this work, parameters of silver nanoparticles ink for micro-scale printed electronics technique, Aerosol Jet Printing, are being enhanced. To increase electrical conductivity and enhance printability, surfactants and dispersing agents were used to increase ultrasonic atomisation efficiency, obtain a uniform structure of printed lines, and narrow the width of printed patterns. Electrical measurements show a decrease in resistivity value in samples enhanced by cationic and non-ionic surfactants, by 95%, compared to initially prepared inks. Surfactant additions to silver nanoparticles Aerosol Jet Printing ink show promising features for application in modern electronics.

20 January 2020 in Electronic Materials Letters
Verified
Journal Article
Open access
PDF file
WAW. Andrysiewicz
W. Andrysiewicz
JKJ. Krzeminski
J. Krzeminski
KSK. Skarżynski
K. Skarżynski
Konstanty Waldemar MarszalekKonstanty Waldemar Marszalek
Konstanty Waldemar Marszalek
MSMarcin Sloma
Marcin Sloma
Artur RydoszArtur Rydosz
Artur Rydosz
Gas sensors are widely used in many industrial and home applications. There is therefore continued need to develop novel gas sensor substrates which provide good mechanical and electrical stability, and good flexibility in comparison with the conventional alumina and silicon-based materials. In this paper, we present the experimental results on flexible gas sensors based on the Kapton foil and alumina substrate covered by copper oxide as a gas-sensitive layer. These sensors exhibited good mechanical stability and gas-sensing characteristics. The Kapton-based CuO gas sensors were tested under exposure to acetone in the 0.05–1.25 ppm range (150 °C, 50%RH). The results confirmed that sensors deposited on the flexible substrate such as Kapton can be used in the exhaled breath analyzers dedicated to diabetes biomarker detection or other applications for which the elastic substrate is needed. Graphic

17 September 2024 in Advanced Functional Materials
Verified
Journal Article
Closed access
MPMuhammad A. K. Purbayanto
Muhammad A. K. Purbayanto
VPVolker Presser
Volker Presser
KSKacper Skarżyński
Kacper Skarżyński
MSMarcin Sloma
Marcin Sloma
MNMichael Naguib
Michael Naguib
Agnieszka JastrzębskaAgnieszka Jastrzębska
Agnieszka Jastrzębska

2 July 2023 in Advanced Electronic Materials
Verified
Journal Article
Open access
KSKacper Skarżyński
Kacper Skarżyński
MSMarcin Słoma
Marcin Słoma
The Internet of Things is currently one of the fastest‐growing branches in electronics. The development of energy storage systems and the miniaturization of dedicated printed circuit boards significantly influence that growth. However, the need for batteries and traditional printed circuit boards still limits devices' minimum size, weight, and cost, narrowing the application area. Energy harvesters and wireless power transfer systems fabricated with printed electronics can significantly reduce such devices' weight, size, and cost. Printed electronics technology provides scalable tools for many electronics applications, shortening the validation time and enabling new low‐cost or disposable solutions on lightweight and flexible substrates embedded inside 3D printed structures and directly on device housings. Energy harvesting and wireless power transfer systems in electronic devices can provide enough power to minimize battery capacity and size or even eliminate the need for batteries in low‐power applications. This review presents an adaptation of printed electronics technology in the fabrication of radio frequency energy harvesters and wireless power transfer rectennas for IoT applications. Last, perspectives for development towards greater integration with microsystems, transient electronics with ecofriendly materials, adaptation for next‐generation telecommunication systems, and 3D structural electronics solutions are briefly discussed.

6 November 2019
Verified
Conference Paper
Closed access
PDF file
KSKacper Skarżyński
Kacper Skarżyński
JKJakub Krzemiński
Jakub Krzemiński
MSMarcin Słoma
Marcin Słoma
Inks for printed electronics developed in the laboratory have several advantages over commercial ones – researchers have full information about the composition and are able to change its properties without the danger of undesirable interactions between the components. The requirement for this type of ink is long term stability in order to utilize its individuals features. Within this paper the difference between freshly created and 3-months old inks was examined to determine the effect of different sonication processes and solvents on the ageing of silver nano-particle ink. Ink was sonicated using a sonotrode and an ultrasonic bath. To examine inks printability in the aerosol jet printing process, their ability to create dense aerosol mist for 1 hour using an ultrasonic atomiser was investigated. Aerosol droplets diameters were measured to compare fresh and 3 months old printable inks.

1 October 2018
Verified
Conference Paper
Closed access
PDF file
JKJakub Krzemiński
Jakub Krzemiński
KSKacper Skarzynski
Kacper Skarzynski
GWGrzegorz Wroblewski
Grzegorz Wroblewski
DJDaniel Janczak
Daniel Janczak
LDLucja Dybowska-Sarapuk
Lucja Dybowska-Sarapuk
Małgorzata JakubowskaMałgorzata Jakubowska
Małgorzata Jakubowska
Aerosol jet printing is a new technology which is able to form a micrometer size patterns directly on the substrate. It is possible due to the special ink treatment - first, the ink is formulated to form a mist or fog with a very small droplets (average size about 1 μm). Then the atomized ink is transported to the printing head. In the printing head, a special shear gas flow focuses the mist into several micrometer size stream. This technology is an additive method which allows printing even on the 3D substrates. The achievement of 10 μm line wide makes it comparable with conventional flat, many stages photolithography. In this article, authors present the self-made printing head for the aerosol jet method and the results of the printing process. The printing process was performed with ultrasonic atomizer and the nanosilver ink. As a result, authors have obtained conductive, 40 μm wide silver lines.