25 October 2022 in IEEE Transactions on Instrumentation and Measurement
Time domain reflectometry (TDR) is an effective method used to detect partial discharge (PD) and localize PD sources on power cables. However, for long-length power cables, the attenuation and dispersion of PD signals are significant due to the propagated distance. The attenuation causes a serious reduction of the pulse amplitude, which makes the defects located far away from the PD detector difficult to find. The dispersion causes appreciable asymmetry in the PD pulse wave form. Thus, the localization accuracy is reduced. To solve the problem of long-length cable fault localization, a novel signal relay system is proposed in this paper. Once a weak PD pulse is captured in the signal relay system, another standard Gaussian pulse signal is initiated by a function generator. The Gaussian pulse signal is injected into the cable and travels along the cable. During this procedure, the weak PD pulse is likely to be amplified, and the fault localization accuracy is notably enhanced. To validate the effectiveness of the proposed method, an experimental platform is built in a laboratory, and PD detection of an artificial defective cable is performed. The experimental results show that the signal relay system can effectively “enlarge” the PD pulse on a long-length cable. For long-length power cables, PD detection can achieve a higher localization accuracy based on the proposed method.
30 October 2024 in IEEE Transactions on Dielectrics and Electrical Insulation
The penetration of moisture into power cable joints accelerates cable insulation degradation, ultimately leading to cable breakdowns and power outages. The determination of whether environmental moisture has penetrated an insulation interface and the discrimination of dampness status are, thus, significant tasks in cable operation, maintenance, and management. Therefore, a dampness discrimination method based on polarization and depolarization current (PDC) testing under thermal stimulation is presented here. Initially, a working principle of the PDC testing method for detecting moisture in cable joints is developed. Subsequently, a thorough description of the principle of dampness discrimination in cable joints is provided based on PDC testing under thermal stimulation. This analysis reveals that thermal stimulation may alter the phase state of water and the interface contact state between cross-linked polyethylene (XLPE) and silicone rubber (SiR), decreasing the conducting current of the cable. In addition, finite element simulations are employed to determine the parameters for the thermal stimulation methods. Finally, experimental results confirm the effectiveness of the proposed method in accurately identifying dampness defects in cable joints.
11 June 2025 in Journal of Applied Physics
Shock waves generated by streamer discharges in transformer oil are a critical factor leading to mechanical damage and explosion incidents in oil-immersed transformers. To clarify the mechanisms of shock wave generation and propagation, this study developed an experimental platform for streamer-induced shock waves and constructed a streamer model based on electrohydrodynamic drift-diffusion, along with a shock wave propagation model driven by volumetric pressure source density. According to the comparison between the simulation and experimental results, the accuracy of the streamer model and the shock wave propagation model was validated. The results show that the high electric field at the streamer tip induces localized ionization, forming plasma clusters. Moreover, plasma clusters generate concentrated volume pressure sources via electron energy absorption, with the source intensity sharply rising to 1.09 × 1020 s−2 upon streamer completion. Subsequently, under high-energy volume pressure sources, the shock wave exhibits typical spherical longitudinal wave characteristics: specifically, a pulse duration of 2.35 μs, a stable central frequency of 417 kHz, and amplitude decay following a power-law model. Finally, the study demonstrates that material interface acoustic impedances significantly alter shock wave behavior. Specifically, the oil–acrylic–air interface generates multi-peak oscillatory waveforms due to multipath interference, while the oil–acrylic interface amplifies wall pressure peaks by 42.1% through constructive interference. This study provides a theoretical foundation for understanding the mechanisms of shock wave generation and propagation induced by streamer discharge in oil.
18 June 2025 in IEEE Transactions on Dielectrics and Electrical Insulation
During the long-term operation of transformers, conductive impurity particles within the transformer oil can significantly degrade its dielectric strength, potentially leading to transformer failures and causing substantial economic losses and adverse social impacts. To comprehensively understand the influence of conductive particles on the discharge characteristics of transformer oil, this paper systematically reviews the progress of relevant research. First, the theoretical framework of force models for conductive particles in transformer oil is introduced, and the effects of voltage type, amplitude, temperature, and flow rate on the motion state, velocity, bridging speed, and landing distance of conductive particles are summarized. Subsequently, the discharge types of transformer oil containing conductive particles are elaborated, and the mechanisms by which factors such as the number of conductive particles and voltage type affect the breakdown voltage are analyzed. The physical mechanisms through which conductive particles induce discharges in transformer oil are also outlined. Finally, methods for the detection and identification of particles in transformer oil are systematically reviewed, with a comparison of the applicability and advantages of different techniques, and future research directions are discussed. This review aims to provide theoretical references and practical guidance for the structural optimization and operational maintenance of transformers.
1 February 2020 in International Journal of Machine Tools and Manufacture