Ulaş Matik

Ulaş Matik

Auto-generated profile, based on publicly available information

Ulaş Matik

Karabuk University

Research Focus & Metrics

Academic Career Length

2Years (2025-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
20 February 2026 in Gazi University Journal of Science
Verified
Journal Article
Closed access
YDYakup Daşdemirli
Yakup Daşdemirli
UMUlaş Matik
Ulaş Matik
MKMuhammet Kayfeci
Muhammet Kayfeci
This study investigates the thermal and mass transfer behaviors of the LaNi5 alloy during hydrogen absorption after applying three different surface coatings. To enhance heat transfer within the metal hydride reactor and evaluate its performance, three reactor designs were developed: a reference design, a design incorporating a central heat pipe, and an advanced design equipped with a finned heat pipe to improve heat distribution. LaNi5 powders were ground for one hour using mechanical milling and then coated under controlled conditions to produce copper-coated, Cu/Ag double-layer-coated, and silver-coated samples. The findings demonstrate that a homogeneous and stable Cu/Ag duplex coating can be successfully applied to LaNi5 powders. This offers the potential to enhance heat transfer in hydrogen storage systems by improving the thermal behavior of metal hydrides. The thermal conductivity of uncoated and coated powders was measured experimentally. Experiments confirmed that higher operating pressures resulted in improved hydrogen absorption. Not only did enhanced thermal conductivity accelerate hydrogen absorption, but it also reduced local temperature spikes, promoting a more uniform temperature distribution throughout the reactor. These values were then used in a three-dimensional model to simulate the hydrogen absorption process. This model assessed the storage capacity of hydrogen and the temperature distribution over time at various operating pressures (3, 6, 9, 10, 12, and 15 bar). Using heat pipes and fins significantly enhanced heat transfer within the reactor, resulting in improved overall performance.

24 June 2026 in SSRN Electronic Journal
Verified
Preprint
Open access
UMUlaş Matik
Ulaş Matik
In this study, A356/WC aluminium matrix composites containing 0, 1, 2, and 3 vol.% WC were fabricated by powder metallurgy followed by hot extrusion. Microstructural analyses revealed that hot extrusion contributed to improved densification and a relatively homogeneous distribution of WC particles at low and intermediate reinforcement levels, whereas excessive WC addition promoted particle agglomeration and increased porosity. X-ray diffraction analysis confirmed the absence of interfacial reaction phases, indicating that WC remained thermodynamically stable and acted as an inert reinforcement within the aluminium matrix. The incorporation of WC resulted in a substantial increase in hardness and a significant reduction in wear volume and coefficient of friction under dry sliding conditions. Tensile testing showed that yield strength and ultimate tensile strength increased up to 1-2 vol.% WC, whereas elongation to fracture decreased progressively with increasing reinforcement content. At 3 vol.% WC, the pronounced reduction in ductility was associated with particle agglomeration, increased porosity, and microstructural heterogeneity. The observed strengthening behavior was primarily attributed to load transfer and the restriction of matrix deformation by the hard WC particles. Among the investigated compositions, 1-2 vol.% WC provided the most favorable balance between strength, wear resistance, and ductility.

29 December 2025 in International Journal of Energy Studies
Verified
Journal Article
Closed access
MKMuhammet Kayfeci
Muhammet Kayfeci
UMUlaş Matik
Ulaş Matik
YDYakup Daşdemirli
Yakup Daşdemirli
The thermal and mass behavior of LaNi5 alloy, a metal hydride-based hydrogen storage material, modified with different surface coating types was investigated during the hydrogen storage process. Based on the experimentally measured thermal conductivity coefficients, four different sample groups were created: Sample 1 – uncoated LaNi5 powder, Sample 2 – copper-coated LaNi5, Sample 3 – copper/silver double-layer-coated LaNi5, and Sample 4 – silver-coated LaNi5. The thermal conductivity values of each sample were determined, and these data were evaluated in a three-dimensional model developed in COMSOL Multiphysics software. During the modeling process, the amount of hydrogen stored in the metal hydride reactor under different operating pressures (4 bar, 8 bar, and 12 bar) was calculated; the transient temperature distribution and hydrogen concentration profiles of the system were analyzed with time. It was shown that the coated samples – especially the Cu, Cu/Ag, and Ag coated samples – had higher thermal conductivities than the uncoated sample. This increase contributes to the shortening of the hydrogen absorption time and the limitation of local temperature increases, resulting in a more homogeneous temperature distribution in the system.

29 December 2025 in International Journal of Energy Studies
Verified
Journal Article
Closed access
MKMuhammet Kayfeci
Muhammet Kayfeci
UMUlaş Matik
Ulaş Matik
YDYakup Daşdemirli
Yakup Daşdemirli
The low thermal conductivity of LaNi₅-based metal hydride powders limits efficient heat removal during hydrogen charging and discharging, thereby reducing overall system efficiency. This study examines the application of a Cu/Ag duplex coating on LaNi₅ metal hydride particles to minimize interparticle thermal resistance and improve thermal conductivity. LaNi₅ particles were first ground in a ball mill for one hour, then coated with Cu via a chemical reduction method in a copper sulfate-containing solution. The Cu/Ag duplex coating was subsequently formed by reducing the Cu-coated surfaces with [Ag(NH₃)₂]⁺ complex ions in a solution containing potassium sodium tartrate (KNaC₄H₄O₆·4H₂O). The structural, morphological, and thermal properties of the coatings were characterized using several techniques. Scanning electron microscopy (SEM) was used to analyze the surface morphology, while energy dispersive X-Ray spectroscopy (EDX) confirmed the elemental composition. X-ray diffraction (XRD) was used to determine the phase structure. Differential scanning calorimetry (DSC) was performed to evaluate thermal stability and potential structural transformations. The results show that a uniform and stable Cu/Ag duplex coating can be successfully applied to LaNi5 powders. DSC analysis further reveals that the duplex coating improves the thermal behavior of metal hydrides, offering a promising method for enhancing heat transfer in hydrogen storage systems.

24 June 2026 in SSRN Electronic Journal
Verified
Preprint
Open access
UMUlaş Matik
Ulaş Matik
In this study, A356/WC aluminium matrix composites containing 0, 1, 2, and 3 vol.% WC were fabricated by powder metallurgy followed by hot extrusion. Microstructural analyses revealed that hot extrusion contributed to improved densification and a relatively homogeneous distribution of WC particles at low and intermediate reinforcement levels, whereas excessive WC addition promoted particle agglomeration and increased porosity. X-ray diffraction analysis confirmed the absence of interfacial reaction phases, indicating that WC remained thermodynamically stable and acted as an inert reinforcement within the aluminium matrix. The incorporation of WC resulted in a substantial increase in hardness and a significant reduction in wear volume and coefficient of friction under dry sliding conditions. Tensile testing showed that yield strength and ultimate tensile strength increased up to 1-2 vol.% WC, whereas elongation to fracture decreased progressively with increasing reinforcement content. At 3 vol.% WC, the pronounced reduction in ductility was associated with particle agglomeration, increased porosity, and microstructural heterogeneity. The observed strengthening behavior was primarily attributed to load transfer and the restriction of matrix deformation by the hard WC particles. Among the investigated compositions, 1-2 vol.% WC provided the most favorable balance between strength, wear resistance, and ductility.