1 December 2023 in IEEE Transactions on Power Electronics
For 4H-SiC mosfet s, the parasitic PiN body diode causes problems such as significant forward voltage drop of body diode and poor reverse recovery characteristics during high-temperature operation. A reasonable solution is a mosfet with an integrated Schottky barrier diode to deactivate the PiN body diode. Since SiC mosfet s can operate at extremely high temperatures, the characterization of electrical parameters at high temperatures and changing with the temperature are very important for high power applications and system reliability. However, there is a lack of comparison and analysis of the two devices on electrical properties at ultrahigh temperatures. In this article, a 1.2 kV conventional mosfet and a mosfet integrated with a junction barrier Schottky diode (JBSFET) were fabricated with a consistent process flow. In the temperature range from 300 to 575 K, analytical models of the temperature-dependent electrical parameters of these two devices were established and compared, which were successfully verified by the measurements. These models can provide guidance for ultrahigh temperature applications of JBSFETs. Temperature-related expressions can also be used for junction temperature monitoring of temperature-sensitive electrical parameters. Experimental results show that JBSFET has better third quadrant conduction characteristics and higher temperature stability below 450 K, but loses obvious performance advantages at 575 K. So, the recommended operating temperature range of JBSFET is from 300 to 450 K. Finally, the continuous operation performance of the body diodes in buck converters is analyzed. The higher efficiency of buck converter based on JBSFET's body diode indicates its great application potential in compact converters, especially in the recommended temperature range.
8 October 2024 in IEEE Transactions on Electron Devices
In this article, a 1.2-kV conventional MOSFET and a MOSFET integrated with a junction barrier Schottky diode (JBSFET) were fabricated with a consistent process flow. The electrical characteristics of MOSFET and JBSFET, including static performance, structural capacitance, and switching performance have been systematically analyzed in the temperature range of 80–300 K. Experimental results show that the third quadrant voltage drop of JBSFET is smaller than MOSFET and hardly changes with decreasing temperature. The gate-drain capacitance of MOSFET and JBSFET increases by more than 50% at 80 K, due to the cryogenic incomplete ionization of the P-Base. The switching performance of the two devices is affected by the temperature dependence of threshold voltage, structural capacitance, and interface state charges, manifesting in a reduction in turn-on speed and voltage tailing at cryogenic temperatures. According to the results, JBSFET has better potential for low-temperature applications due to its stable third-quadrant characteristics. The cryogenic incomplete ionization of the P-Base region has a significant impact on the output characteristics, structural capacitance, and switching performance.
12 July 2024 in IEEE Transactions on Power Electronics
Degradation of SiC power mosfet s under repetitive short-circuit (SC) stress is significant to the reliability of the power systems. A deep level transient spectrum method together with split C-V method to split the trap characteristics of the SiC mosfet s is proposed. The degradation details of different locations in SiC planar gate (PG) and trench gate (TG) mosfet s are comprehensively studied in this article. Thus, a criterion is provided to guide the SC degradation from the aspect of traps. The main degradation of the channel region is the increase of border traps for PG mosfet and newly generated interface traps for TG mosfet . The interface traps domain the degradation in the JFET region for both devices. The degradations of gate oxide for both devices affect the channel and JFET regions especially in the first set of SC cycles. The degradation of body diode is mainly influenced by hole traps in PG mosfet , but by electron traps first then hole traps newly generated in TG mosfet . Finally, the degradation locations of PG and TG mosfet s are effectively characterized. It is the first time to use the trap measurement method to separate the different degradation in every part of the devices in detail. The method proposed in this article can better reflect the failure mechanisms related to dynamics and evaluate the operation of devices effectively, which provides very useful guidance for the reliability design and utilization of SiC mosfet s.
10 February 2026 in IEEE Transactions on Electron Devices
This work proposes a novel self-activated gate-clamping (SAGC) silicon carbide (SiC) MOSFET to enhance the short circuit (SC) capability. The clamp MOSFET, integrated in the power MOSFET, is normally off. The clamp MOSFET is mainly activated by the high temperature of around 1220 K under SC conditions, well below its thermal runaway temperature of 1620 K. This can form a low-resistance path between the power gate (PG) and source. The SAGC MOSFET can increase the SC withstand time from several $\mu $ s to an almost limitless value, as verified at different bus voltages of 400, 600, and 800 V, respectively. Furthermore, the proposed SAGC MOSFET has the advantage of being combined with the multicell MOSFET. This combination overcomes the extra area introduced by the clamp MOSFET, thereby reducing the equivalent cell pitch. The combined MOSFET is verified at 400-V bus voltage. It activates at $10~\mu $ s, suppressing thermal runaway and significantly improving the SC withstand time. The proposed novel SAGC MOSFET successfully realizes the same SAGC function and exhibits a uniform circuit density distribution, demonstrating an excellent intrinsic device self-protection capability.
14 September 2026 in Applied Physics Letters
Oxygen vacancies (VO) at the β-Ga2O3 surface are associated with the high interface-trap densities (Dit, 1012–1013 cm−2 eV−1) that limit the threshold-voltage stability in Al2O3/β-Ga2O3 MOS devices. We combine first-principles calculations with Raman spectroscopy, photoluminescence (PL), x-ray photoelectron spectroscopy, and electrical characterization to examine how supercritical-fluid processing modifies these interface states. Perdew–Burke–Ernzerhof calculations with a rigid scissor correction to the experimental 4.8 eV bandgap identify in-gap states associated with the three inequivalent VO sites. Interstitial oxygen removes these states in the calculated model and increases the migration barrier from 0.08 to 1.8 eV. Experimentally, supercritical N2O (SN) treatment narrows the Raman linewidths at 347, 416, and 767 cm−1, suppresses the 2.4 and 2.8 eV defect-related PL bands, and increases the lattice-oxygen fraction from approximately 50% to more than 80%. A near-critical CO2 pre-clean further improves the SN response, consistent with removal of surface adsorbates before oxidation. The resulting NCSN process reduces Dit to 1.5 × 1011 cm−2 eV−1, lowers Nit by a factor of 6.4, and decreases the positive-bias-stress flatband-voltage shift from 0.79 to 0.23 V. Together, the calculations and measurements support oxygen vacancy filling and reduced oxygen migration as the main contributors to interface passivation.