17 July 2020 in Journal of Advanced Concrete Technology
BSBoonchai Stitmannaithum
This paper presents an experimental and numerical investigation on concrete members strengthened by embedded through-section (ETS) steel and glass fiber-reinforced polymer (GFRP) bars attached preferably with mechanical anchorage at the tension ends. The pullout tests to analyze the bond performance between ETS bars and concrete under various influences such as anchorage presence, embedment length, ETS bar diameter, ETS-material types, and anchorage length are carried out. An analytical method for deriving the local bond stress-slip relationship of GFRP bars-concrete interfaces is developed. The overall responses of the pullout test specimens in terms of pullout force-slip curves, failure modes and strain profiles along the embedment length are discussed. Based on a careful interpretation, the analytical results demonstrated the effectiveness of the local bond stress-slip model developed in this study. Additionally, the finite element (FE) simulation of the beams intervened with ETS bars, which were tested in a previous study by the authors, incorporating with the proposed interfacial model is conducted. Comparison between the results achieved from the FE modelling and the experiment implies that the FE method was an accurately applicable tool to assess the behaviors of the beams strengthened in shear by ETS bars.
1 October 2020 in Journal of Composites for Construction
BSBoonchai Stitmannaithum
This paper presents an experimental investigation on reinforced concrete (RC) beams strengthened in shear with embedded through-section (ETS) steel and fiber reinforced polymer (FRP) bars anchored with and without a mechanical anchorage system. The responses of the beams, including the load–deflection relationship, crack patterns, modes of failure, and reinforcement strain, are discussed. In addition, the shear performances of different strengthening systems are analyzed by comparing the ETS cases with ordinary reinforcement techniques. The effects of different types of ETS strengthening are considered in the presence of varying numbers of steel stirrups. An investigation of the shear contribution of the strengthening bars is carried out to assess the applicability of existing models. An average strain equation for ETS-FRP bars is developed from original models. Comparisons of the results obtained from this paper with those reported in the literature demonstrate that the end anchored ETS strengthening system provides a significant improvement in the shear strengthening efficiency. Furthermore, the truss analogy combined with the developed average strain formulation is an effective method to predict the shear resisting force of anchored ETS-FRP bars in ETS-FRP strengthened beams.
14 November 2018 in Journal of Advanced Concrete Technology
BSBoonchai Stitmannaithum
This paper presents a numerical investigation of the mechanical performance and ductility of concrete beams reinforced by both fiber-reinforced polymer (FRP) and steel tension reinforcement. Three-dimensional (3D) finite element (FE) analysis of beams with both FRP and steel reinforcement was conducted by first using ANSYS to verify the reliability of the FE analysis. The FE analysis can predict the mechanical behavior of the tested beams. To evaluate the ductility of the FRP-steel reinforced concrete (RC) beams considering various factors, such as the effects of the FRP on the steel reinforcement ratio, the location of the FRP reinforcement, the FRP type and the concrete compressive strength, on the mechanical performance of the beams, a parametric study was used to complement the FE analysis. Based on the parametric study, the conditions of the ratio of FRP to steel reinforcement, the location of the FRP reinforcement and the type of FRP reinforcement required to obtain reasonable ductility in practical use were presented.
1 October 2022 in Journal of Composites for Construction
BSBoonchai Stitmannaithum
The structural performance of reinforced concrete (RC) beams strengthened in shear with embedded through-section (ETS) glass fiber-reinforced polymer (GFRP) bars is experimentally and analytically investigated. Three-point bending tests are performed. The investigated parameters include the number of existing steel stirrups (ρsw = 0.28%), concrete compressive strength ( = 27 and 43 MPa), shear span-to-effective depth ratio (a/d = 2.4, 3.6, and 4.8), anchorage presence (with and without anchorage), and anchorage properties (steel and GFRP anchorage systems, as well as the anchorage length). The results indicate that the shear capacity and stiffness of the beams are enhanced by applying ETS-GFRP, increasing concrete strength, and decreasing shear span-to-effective depth ratio. The ETS-GFRP-strengthened beams exhibit a more ductile failure mode than the unstrengthened beam owing to concrete crushing in loading areas. The beam stiffness depends significantly on the anchorage presence and properties, and the beam shear capacities differ considerably for different anchorage systems. Anchorage with four steel nuts or two GFRP nuts at the ETS bar ends provides the highest shear resistance and stiffness for the ETS-strengthened beams. The results of this study suggest that the details and configuration of the anchorage system should be carefully considered for the development of unanimous specifications. Additionally, previously proposed shear models can be used to conservatively analyze test results with sufficient accuracy. The newly developed model for estimation of the shear strengths of ETS-GFRP-strengthened beams and the effective strains in ETS-GFRP bars agrees well with the test data.
1 May 2020 in Journal of Building Engineering
BSBoonchai Stitmannaithum