29 December 2021 in Eastern-European Journal of Enterprise Technologies
This paper reports a method for improving the firing efficiency of an artillery unit that results in enhanced effectiveness. Given the modern use of artillery for counter-battery warfare, the effectiveness of shooting is not enough assessed by accuracy only. It is also necessary to take into consideration and minimize the time spent by the unit in the firing position and the consumption of shells to hit the target. It has been shown that in order to assess the effectiveness of an artillery shot due to the initial velocity of the projectile, the most rapid and simple means is to classify the quality of the shot by the acoustic field. A procedure for categorizing the shot has been improved by applying an automatic classifier with training based on a machine of support vectors with the least squares. It is established that the error in the classification of the effectiveness of the second shot does not exceed 0.05. The concept of the effectiveness of a single artillery shot was introduced. Under the conditions of intense shooting, there may be accidental disturbances in each shot due to the wear of the charging chamber of the gun, its barrel, and incomplete information about the powder charge. When firing involves disturbances, the firing of an artillery unit can be described by a model of a discrete Markov chain. Based on the Markov model, a method for improving the efficiency of artillery fire has been devised. The method is based on the identification of guns that produce ineffective shots. The fire control phase of the unit has been introduced. In the process of controlling the fire of the unit, such guns are excluded from further firing. A generalized criterion for the effectiveness of artillery firing of a unit, based on the convolution of criteria, has been introduced. It is shown that the devised method significantly improves the effectiveness of shooting according to the generalized criterion.
31 August 2021 in Eastern-European Journal of Enterprise Technologies
A phenomenon that is present in almost every shot is highlighted. It manifests itself in the muzzle discharge as a certain amount of free carbon. The thermochemical reaction of Boudouard-Bell (disproportionation of carbon monoxide) was determined, which explains the formation of free carbon in the gunpowder gases during the firing process. A feature of this reaction is the formation of a condensed phase of carbon during the firing process after the gasification of the gunpowder charge. The reason is revealed that does not allow describing the formation of free carbon during firing on the basis of existing models of internal ballistics processes. It is the lack of taking into account the temperature distribution of the gunpowder gases along the length of the gun barrel and its change. A mathematical model is proposed that makes it possible to estimate the temperature distribution during the shot. A method has been developed for solving the problem of internal ballistics with the ability to determine the temperature of gunpowder gases along the length of the gun barrel at different times and at different positions of the projectile in the barrel. The original model is built using generally accepted assumptions. Modeling results can only be estimated. For this reason, the method is based on simple calculations, which makes it possible not to involve high-power computing equipment. The modeling of the temperature distribution of gunpowder gases in the space of the gun barrel between the charging ball and the moving projectile in the model system is carried out. The possibility of changing the length of the zone of the Boudouard-Bell reaction (the zone of formation of free carbon) depending on the initial data is shown. The use of a fresh gunpowder charge and a degraded one is simulated. Full and reduced charges are considered. The simulation results showed the reason for the possibility of initiating a secondary muzzle discharge flash both from the front side and from the side of the muzzle brake.
10 September 2024 in EUREKA: Physics and Engineering
The range of changes in the characteristics of powder mixtures, even of the same brand, expands due to different storage periods and progressive degradation of the powders. The need to simplify the procedure for determining the composition and energy characteristics of the powders used is emphasized. The purpose of simplification is to increase the number of quality control points for incoming charges, bring them closer to combat formations, and reduce the requirements for service personnel. It is proposed to determine the actual composition and energy characteristics of the powder charge based on the library method. This approach requires a large amount of calculations – multiple solutions to the problem of equilibrium conversion of the original powder mixture into combustion products. But these calculations for a given brand of powder are carried out in advance, once and in laboratory conditions. The characteristics of a specific charge sample are determined using library data based on the measured technological parameters of its combustion process - the mass of the burned sample and the temperature of the powder gases. To be able to take into account soot formation and gaseous products of thermal destruction of powder when solving problems for filling the library, the equilibrium model of such a process has been modernized. Instead of partial pressures and concentrations of substances, their mole fractions are considered. The use of partial pressures is convenient when there are only gaseous products. The use of mole fractions made it possible to uniformly take into account the gaseous and condensed phases of combustion products. The modernized calculation model was verified by comparing the obtained results with known data. The need to validate the list of combustion products in each case under consideration was determined
28 March 2025 in EUREKA: Physics and Engineering
Long-range artillery remains vital in modern warfare, where precision and innovative methods are key to completing fire missions with fewer rounds. Developing advanced techniques of artillery shots verification based on sensor systems that maximize target destruction with minimal ammunition and exposure time is essential for maintaining the combat effectiveness of artillery units. Moreover, one of the complex and important tasks that must be solved in the verification process before each shot is to determine the optimal combination of three sensors from the entire available set included in the sensor system in the firing zone. To solve this problem the paper introduces an approach for selecting the three most appropriate acoustic sensors for artillery shot verification using a fuzzy evaluation model. The approach considers location, measurement error, and probability of failure-free operation at selecting sensors to effectively register ballistic and muzzle waves, with further assessment of the suitability of each sensor. For adequate assessment of acoustic sensors, the presented approach uses a developed fuzzy logic model that allows calculating the value of the sensor suitability criterion for the verification of the current artillery shot. A computational experiment with fixed artillery shot parameters was conducted to evaluate the proposed approach and fuzzy model, successfully identifying three optimal acoustic sensors for precise recording of ballistic and muzzle waves. The obtained results confirm the effectiveness and feasibility of the proposed approach and fuzzy model for selecting the best sensors for artillery shot verification and determining projectile impact coordinates under random disturbances.