1 January 2013 in Energy Procedia
In recent, production of bioethanol in Indonesia is produced primarily from sugarcane molasses and cassava as the 1st generation. But related with its development, it is quite hard to be a major feedstock in bioethanol conversion because there is conflict in using between consumption food and energy resources. Due to abundant lignocellulose biomass resources in Indonesia, such as empty fruit bunch (EFB) of oil palm, sugarcane bagasse and other forrest residue, the research in the development of process for 2nd generation bioethanol production is being increase. This case can be a right solution to solve the problem because lignocellulose is unused material. Processing of lignocellulosic biomass into bioethanol consists of four major unit operations: pre-treatment, hydrolysis, fermentation and product separation/distillation. Although ethanol is the dominant alcohol produced in the fermentation of sugars process, there are some byproducts in bioethanol product, such as organic impurities, water and organic acid. Determination of the impurity is important to prove the quality of produced bioethanol. Some of the impurities is not allowed in the product, such as methanol and others organic, that should be limited to control the performance from bioethanol as substituted fuel. Organic impurities of the bioethanol product was analyzed by using GC-FID while the water content was analyzed by using Karl Fischer Coulometric Moisture Titrator. In this research, the lignocellulosic bioethanol analyzed for the moisture content and organic impurities was undenatured one. The water content of the bioethanol sample was analyzed in 7 replicates where the average was 0.1776%-w (% RSD 2.0460). There are eight compounds of organic impurities detected in GC-FID that are acetaldehyde (0.0217%-w), acetone (0.0102%-w), ethyl acetate (0.0368%-w), methanol (0.0224%-w), isopropyl alcohol (0.0035%-w), n-propyl alcohol (0.0188%-w), isobutanol (0.0437%-w) and isoamyl alcohol (0.0377%-w)
30 September 2021 in Cellulose Chemistry and Technology
This study aimed to investigate the effect of adding CO2 as an impregnation agent in steam explosion on oil palm empty fruit bunch (EFB) for bioethanol production. The influence of this treatment on the characteristics of EFB, enzymatic hydrolysis, and fermentation of EFB was evaluated in this investigation. CO2-added steam explosion was conducted varying the CO2 impregnation time (0, 30, 60 min). The results showed that the addition of CO2 in steam explosion increased the surface area, pore area, and pore volume of EFB. Furthermore, this treatment enabled obtaining yields of glucose and ethanol of 84.14% and 56.01%, respectively, for 60 min CO2 impregnation time. These results were higher than the glucose and ethanol yields of the sample treated by conventional steam explosion, which reached 58.12% and 41.37%, respectively. The findings illustrate the possibility of applying CO2-added steam explosion (CO2SE) for increasing the efficiency of biomass conversion.
23 May 2022 in Jurnal Kimia Sains dan Aplikasi
Lignin, the second most abundant natural polymeric globally, is considered the source of the renewable aromatic compound. It serves as an alternative feedstock for the elaboration of chemicals and polymers. However, even until now, it is still primarily used as a low-value fuel for boilers. In the current research, alkaline lignin was modified and used as an adsorbent for removing lead (Pb) in an aqueous solution. The functionalized alkaline lignin (FAL) was prepared by a Mannich reaction with formaldehyde and dimethylamine, followed by esterification of carbon disulfide. The FAL was characterized using CHN elemental analysis, X-Ray Fluorescence (XRF), Scanning Electron Microscopy (SEM), and Fourier Transform Infrared (FT-IR) to observe the changes in composition, morphology, and chemical structure. The analysis revealed that alkaline lignin was successfully modified using amine and carbon disulfide. The adsorption study shows that the lead concentration reduced to 93.7% after 2 hours in contact with FAL. The FAL adsorption capacity could obtain 0.44 mmol/g of lead.
13 September 2026 in Journal of Environmental Chemical Engineering
MHMuhammad Amin Habibillah
+3
16 November 2026 in Journal of Environmental Management