Killer defects are responsible for leakage current and breakdown in β-gallium oxide (β-Ga2O3) Schottky barrier diodes, which are crucial for power device applications. We have found that stacking faults in the halide vapor phase epitaxial (HVPE) (001) layer are killer defects. One type of defect is found to consist of (111) and (1 1) stacking faults. The leakage current is 50 nA/defect at 200 V. This defect appears as a heart-shaped etch pit. Another type of defect is found to be a sequence of stacking faults from microparticles, which are formed at low gas flow rate during HVPE growth. The leakage current is 0.11–0.49 μA/defect at 200 V. This defect appears as a group of bullet-shaped etch pits.
We utilized ultra-high sensitive emission microscopy to investigate the origin of reverse leakage current of edge-defined film-fed grown (001) β-Ga2O3 Schottky barrier diodes. In the emission patterns, we observed a partially appearing void, having a typical width and depth of 300 and 83 nm, respectively, with a base angle of 75°, below the Schottky barrier contact on the β-Ga2O3 surface. Simulations show that the electric field at the bottom of the void reached 9 × 106 V/cm at a reverse bias of 60 V and in the case of an ideally flat surface 3.1 × 106 V/cm. This indicates that the reverse leakage current originates from an electric field concentration in the partially appearing voids on the surface. On the other hand, we have confirmed that there is no clear relationship between the leakage current path and the dislocations observed by synchrotron x-ray topography.
Identification of the killer defects is crucial for the development of β-Ga2O3 Schottky barrier diodes as power electronic devices. We observed the emission patterns that are exhibited by the high reverse leakage current SBDs via ultrahigh-sensitivity emission microscopy, thereby locating a polycrystalline defect on the surface via atomic force microscopy. A single polycrystalline defect resulted in a leakage current of ca. 20 μA. The synchrotron X-ray topographic analysis of the samples showed butterfly-shaped contrast patterns due to the strain field around the polycrystalline defects. We further observed that a polycrystalline defect is formed over a porous particle.
We observed line-shaped defects in halide vapor-phase epitaxial (001) β-Ga2O3 SBDs. Light emission patterns, representing the reverse leakage current, were observed at these line-shaped defects. In atomic force microscopy observations, the line-shaped defects appeared as grooves with a typical depth and width of 113 and 520 nm, respectively. Such defects corresponded to a leakage current of 0.23 μA at −200 V. Simulation results indicated that the electric field, with an intensity of 1.3 MV/cm, was highly concentrated at the bottom of the line defects. According to the cross-sectional scanning transmission electron microscopy analysis, the line-shaped defects were generated from a dislocation network beneath the crystal near the surface.
Dislocation responsible for leakage current in a halide vapor phase epitaxial (HVPE) (001) β-Ga2O3 Schottky barrier diode (SBD) was explored via ultrahigh-sensitive emission microscopy, synchrotron X-ray topography, and scanning transmission electron microscopy (STEM). Light emission due to the reverse leakage current was observed at the dislocation position with a leakage current of −0.98 μA at −100 V. Moreover, the dislocation is visible for the g vectors of 605 and 225; however, it is invisible for and . The b was determined to be from the g·b invisible criteria. This dislocation was determined mixed-type.
In this study, we identify the killer defect responsible for the reverse leakage in the halide vapor phase epitaxial (011) β-Ga2O3 Schottky barrier diode via ultrahigh sensitive emission microscopy, synchrotron x-ray topography, and scanning transmission electron microscopy. A polycrystalline defect was found to be causing a leakage current of −5.1 μA at a reverse bias of −50 V. They were distributed across the wafer with a density ranging from 10 to 103 cm−2. Cross-sectional scanning electron microscopy of the polycrystalline defect revealed domains with various crystal orientations accompanied by a (100)-oriented micro-crack and dislocations along the [010] direction.