β-Ga2O3 bulk crystals were grown by the edge-defined film-fed growth (EFG) process and the floating zone process. Semiconductor substrates containing no twin boundaries with sizes up to 4 in. in diameter were fabricated. It was found that Si was the main residual impurity in the EFG-grown crystals and that the effective donor concentration (Nd − Na) of unintentionally doped crystals was governed by the Si concentration. Intentional n-type doping was shown to be possible. An etch pit observation revealed that the dislocation density was on the order of 103 cm−3. Nd − Na for the samples annealed in nitrogen ambient was almost the same as the Si concentration, while for the samples annealed in oxygen ambient, it was around 1 × 1017 cm−3 and independent of the Si concentration.
Killer defects are responsible for leakage current and breakdown in β-gallium oxide (β-Ga2O3) Schottky barrier diodes, which are crucial for power device applications. We have found that stacking faults in the halide vapor phase epitaxial (HVPE) (001) layer are killer defects. One type of defect is found to consist of (111) and (1 1) stacking faults. The leakage current is 50 nA/defect at 200 V. This defect appears as a heart-shaped etch pit. Another type of defect is found to be a sequence of stacking faults from microparticles, which are formed at low gas flow rate during HVPE growth. The leakage current is 0.11–0.49 μA/defect at 200 V. This defect appears as a group of bullet-shaped etch pits.
The influence of substrate orientation on homoepitaxial growth of beta-gallium oxide by halide vapor phase epitaxy was investigated. Substrates were cut at various angles Δb from the (001) plane (Δb = 0°) to the (010) plane (Δb = 90°) of bulk crystals grown by the edge-defined film-fed growth method. The growth rate increased with increasing absolute value of Δb near the (001). However, from the (001) to the (010), as Δb increased, the growth rate decreased sharply, and streaky grooves observed in the grown layer on the (001) substrate became triangular pits. The length of the pits decreased with increasing Δb, and a pit-free homoepitaxial layer grew at Δb ≈ 60°. The valley line of the pits was parallel to the [010] direction; therefore, the length of the pits decreased with increasing Δb. In addition, transmission electron microscopy observations of the deepest part of a pit revealed that the pits originate from dislocations propagating in the substrate at an angle of 60° with respect to the (001) plane. Therefore, pits are not formed on the grown layer surface when the Δb of the substrate is ∼60°, because its surface is substantially parallel to the dislocations. The homoepitaxial growth of a pit-free layer on the (011) substrate (Δb = 61.7°) was demonstrated, and void defects and dislocations in the substrate were confirmed by the etch-pit method to not be inherited by the homoepitaxial layer.
We utilized ultra-high sensitive emission microscopy to investigate the origin of reverse leakage current of edge-defined film-fed grown (001) β-Ga2O3 Schottky barrier diodes. In the emission patterns, we observed a partially appearing void, having a typical width and depth of 300 and 83 nm, respectively, with a base angle of 75°, below the Schottky barrier contact on the β-Ga2O3 surface. Simulations show that the electric field at the bottom of the void reached 9 × 106 V/cm at a reverse bias of 60 V and in the case of an ideally flat surface 3.1 × 106 V/cm. This indicates that the reverse leakage current originates from an electric field concentration in the partially appearing voids on the surface. On the other hand, we have confirmed that there is no clear relationship between the leakage current path and the dislocations observed by synchrotron x-ray topography.
We observed line-shaped defects in halide vapor-phase epitaxial (001) β-Ga2O3 SBDs. Light emission patterns, representing the reverse leakage current, were observed at these line-shaped defects. In atomic force microscopy observations, the line-shaped defects appeared as grooves with a typical depth and width of 113 and 520 nm, respectively. Such defects corresponded to a leakage current of 0.23 μA at −200 V. Simulation results indicated that the electric field, with an intensity of 1.3 MV/cm, was highly concentrated at the bottom of the line defects. According to the cross-sectional scanning transmission electron microscopy analysis, the line-shaped defects were generated from a dislocation network beneath the crystal near the surface.
Dislocation responsible for leakage current in a halide vapor phase epitaxial (HVPE) (001) β-Ga2O3 Schottky barrier diode (SBD) was explored via ultrahigh-sensitive emission microscopy, synchrotron X-ray topography, and scanning transmission electron microscopy (STEM). Light emission due to the reverse leakage current was observed at the dislocation position with a leakage current of −0.98 μA at −100 V. Moreover, the dislocation is visible for the g vectors of 605 and 225; however, it is invisible for and . The b was determined to be from the g·b invisible criteria. This dislocation was determined mixed-type.