14 April 2023 in IEEE Transactions on Power Electronics
A novel two-mode inverter-based open-winding permanent magnet synchronous motor drive is proposed in this article. The proposed drive operates in hybrid-inverter mode at low and medium speed to achieve high power quality. The common dc-bus mode is adopted at high speed to fulfill a wider speed range than hybrid-inverter mode. Based on the proposed drive, a modulation strategy for any voltage ratio is proposed, which integrates the instantaneous floating capacitor (FC) voltage into modulation to synthesize the reference voltage vector. The proposed modulation strategy can not only guarantee the FC voltage regulation but also start the drive when the FC voltage is zero and switch the mode of the drive smoothly. Besides, the excellent fault-tolerant capability of the proposed drive is studied under open-phase and switch faults. In the proposed fault-tolerant control, a sinusoidal zero-sequence current is injected to tolerate the open-phase fault in the common dc-bus mode and redundant switching combinations are used to tolerate switch faults in the hybrid-inverter mode. All the claimed advantages have been validated by experimental results.
18 July 2024 in IEEE Transactions on Industry Applications
Deadbeat predictive current control (DPCC) can track the current command with a two-sample step response. However, voltage insufficiency is common during abrupt torque changes, and the current command tracking performance is inevitably degraded. To address this issue, an optimized overmodulation method is developed in this paper. By predicting the current vector hexagon in the subsequent switching period, the crossing point between the predicted current hexagon boundary and the expected current trajectory is determined as an optimized current reference. The purpose is to mitigate the current trajectory drift in the overmodulation zone, thus ensuring optimal dynamic trajectory tracking performance and voltage utilization. The solution of the crossing point is solved by the dichotomy due to the randomness of the expected trajectory. By combining DPCC with the proposed method, dynamic current reference optimization and deadbeat response in the overmodulation zone can be achieved, and accurate current trajectory tracking can be realized. Taking $i_{d}=0$ and $i_{d}=-i_{q}$ trajectory tracking as validation examples, the proposed method is compared with the traditional methods. Both simulation and experimental results have verified the effectiveness of the proposed method.
17 April 2024 in IEEE Transactions on Transportation Electrification
By exploiting inductance or resistance saliency, pulsating high frequency (HF) signal injection is a good candidate for sensorless operations in surface-mounted permanent magnet synchronous motors (SPMSM). However, accurate methods for quantifying inductance or resistance saliency remain incomplete, especially for motors with ultra-low or even no inductance saliency. This research introduces a unique perspective to analyze and quantify the effective rotor anisotropic components. Firstly, parallel equivalent circuits are established to decouple the HF current responses, thereby facilitating the separation of effective rotor anisotropic components under different saliency tracking methods. Secondly, pulsating HF excitations are injected into the finite element analysis (FEA) models, and effective anisotropic components can be extracted at various position tracking errors. Thirdly, to verify the proposed quantification method, rotating HF signals are employed to detect the rotor anisotropic characteristics, with HF equivalent parameters subsequently inverse-calculated via Fourier analysis. The FEA results demonstrate the accurate quantification of effective anisotropic components under different saliency-based tracking methods. Finally, experimental results prove the feasibility of the proposed method. In summary, this research provides an analysis guideline and quantification method for evaluating the rotor anisotropic characteristics.
21 February 2025 in IEEE Transactions on Industry Applications
Radial vibration suppression in motor control can be realized by off-line calibration methods such as multi-physical co-simulation or traversal searching to find the best injected current harmonics. However, these methods are often prone to mechanical installation, temperature changes, and other uncertainties in practice. By contrast, this paper presents a method utilizing the real-time radial acceleration signals to suppress the motor radial vibration and achieve further noise attenuation under real-world uncertainties. To realize fast convergence of the optimal injected harmonics, a self-adaptive-selected-harmonic (SASH) radial vibration suppression strategy of permanent magnet synchronous motor (PMSM) is developed. Based on the pole-slot combination, the harmonic order of the most influential vibration is theoretically calculated. Then, with the radial acceleration signal acquired by a motor-housing-installed accelerometer, the real-time amplitude of the target vibration order is extracted, followed by a fast simulated annealing algorithm to search the optimal amplitude and phase of injected voltage harmonics. Experiments have verified the effectiveness of this proposed strategy, which achieves the suppression of selected-harmonic vibration from 0.03g to below 0.005g, as well as more than 8 dBA average attenuation of the selected-harmonic radial acoustic noise in a wide speed range.
13 January 2025 in IEEE Transactions on Transportation Electrification
Voltage oscillation is an essential concern in dc-link capacitance motor drive system, and various stability assessment and active damping control strategies have been developed using impedance network analysis. However, existing techniques primarily focus on power disturbances caused by rectification, with relatively limited discussion on disturbance loops, particularly the bidirectional disturbance transmission between the dc-link and motor stage. This manuscript explores all disturbance loops within the cascaded system, covering the dc-link stage, the motor stage, and their bidirectional transmission. In addition, an innovative decoupling modeling method is proposed to express the bidirectional disturbance interaction, where the dynamic behavior at the motor stage is treated as an equivalent dc-link current disturbance. Furthermore, particular attention is paid to the additional dc-link voltage oscillations caused by the motor behaviors. These additional oscillations are then superimposed on the motor stage, potentially degrading the expected control performance. Taking the motor speed command disturbance as a case, the control structures and transfer functions of each disturbance loop are deduced. The strong agreement between the analytical expressions and the frequency-sweeping method in simulations confirms the accuracy of the proposed method. Furthermore, the dc-link voltage oscillation induced by motor behavior was successfully validated through experimentation. In short, a general analytical modeling process was presented, along with potential areas for improvement.