1 January 2007 in Vehicle System Dynamics
A systematic methodology is applied in an effort to select optimum values for the suspension damping and stiffness parameters of two degrees of freedom quarter-car models, subjected to road excitation. First, models involving passive suspension dampers with constant or dual rate characteristics are considered. In addition, models with semi-active suspensions are also examined. Moreover, special emphasis is put in modeling possible temporary separations of the wheel from the ground. For all these models, appropriate methodologies are employed for capturing the motions of the vehicle resulting from passing with a constant horizontal speed over roads involving an isolated or a distributed geometric irregularity. The optimization process is based on three suitable performance criteria, related to ride comfort, suspension travel and road holding of the vehicle and yielding the most important suspension stiffness and damping parameters. As these criteria are conflicting, a suitable multi-objective optimization methodology is set up and applied. As a result, a series of diagrams with typical numerical results are presented and compared in both the corresponding objective spaces (in the form of classical Pareto fronts) and parameter spaces.
1 October 2012 in Mechanical Systems and Signal Processing
1 February 2015 in Journal of Manufacturing Science and Engineering
In collaboration with Airbus-UK, the dimensional growth of aircraft panels while being riveted with stiffeners is investigated. Small panels are used in this investigation. The stiffeners have been fastened to the panels with rivets and it has been observed that during this operation the panels expand in the longitudinal and transverse directions. It has been observed that the growth is variable and the challenge is to control the riveting process to minimize this variability. In this investigation, the assembly of the small panels and longitudinal stiffeners has been simulated using static stress and nonlinear explicit finite element models. The models have been validated against a limited set of experimental measurements; it was found that more accurate predictions of the riveting process are achieved using explicit finite element models. Yet, the static stress finite element model is more time efficient, and more practical to simulate hundreds of rivets and the stochastic nature of the process. Furthermore, through a series of numerical simulations and probabilistic analyses, the manufacturing process control parameters that influence panel growth have been identified. Alternative fastening approaches were examined and it was found that dimensional growth can be controlled by changing the design of the dies used for forming the rivets.
8 February 2014 in Structural and Multidisciplinary Optimization
27 April 2017 in International Journal of Crashworthiness
Very fast full vehicle simulations through the use of effective, but drastically simplified digital models is a topic of great interest to automotive manufacturers and research communities. A non-conventional modelling and simulation approach using the macro-element methodology, embedded in Visual Crash Studio (VCS), is assessed. Modelling practices for converting finite element models to macro-element models are developed and presented. A large number of automotive systems, ranging from components and sub-systems to full vehicle models, is investigated. Numerical results obtained from VCS and the finite element code LS-DYNA compared moderately in the majority of the cases. The accuracy and efficiency of the macro-element methodology for vehicle crashworthiness analysis as well as the necessity for model corrections are discussed. Through improved functionality and accuracy, the macro-element methodology could potentially enable engineers to evaluate multiple conceptual designs in shorter times and revolutionise the vehicle development phase.
30 June 2008 in Proceedings of the Institution of Mechanical Engineers, Part K: Journal of Multi-Body Dynamics
Dynamic response of a large order mechanical model of an urban bus is investigated in this paper. The emphasis is first put on developing a quite complete model, which can be utilized in order to extract sufficiently reliable and accurate information related to its dynamics in a fast way. Since some of the components of the bus undergo large rigid body rotation, in addition to motion resulting from their deformability, a multi-body dynamics framework is adopted. This implies that the resulting equations of motion appear in the form of a strongly non-linear set of differential-algebraic equations, which are difficult to handle even numerically. In fact, the modelling becomes more involved because all the significant non-linearities appearing in the interconnections of the structural components and especially in the front and rear suspension subsystems of the bus are taken into account. In order to alleviate some of these complexities, the number of degrees of freedom of each component, associated with its deformability, is reduced drastically by applying an appropriate coordinate condensation methodology. Finally, this model is employed and numerical results are obtained for motions resulting from typical road excitation. In particular, selected response quantities related to ride comfort are examined for characteristic combinations of the bus suspension stiffness and damping parameters.