The KCNK4 gene, predominantly distributed in neurons, plays an essential role in controlling the resting membrane potential and regulating cellular excitability. Previously, only two variants were identified to be associated with human disease, facial dysmorphism, hypertrichosis, epilepsy, intellectual/developmental delay, and gingival overgrowth (FHEIG) syndrome. In this study, we performed trio-based whole exon sequencing (WES) in a cohort of patients with epilepsy. Two de novo likely pathogenic variants were identified in two unrelated cases with heterogeneous phenotypes, including one with Rolandic epilepsy and one with the FHEIG syndrome. The two variants were predicted to be damaged by the majority of in silico algorithms. These variants showed no allele frequencies in controls and presented statistically higher frequencies in the case cohort than that in controls. The FHEIG syndrome-related variants were all located in the region with vital functions in stabilizing the conductive conformation, while the Rolandic epilepsy-related variant was distributed in the area with less impact on the conductive conformation. This study expanded the genetic and phenotypic spectrum of KCNK4. Phenotypic variations of KCNK4 are potentially associated with the molecular sub-regional effects. Carbamazepine/oxcarbazepine and valproate may be effective antiepileptic drugs for patients with KCNK4 variants.
Traditional resonant converters generally use Pulse Frequency Modulation (PFM), which can easily lead to a wide range of switching frequency changes in wide input and light load applications, resulting in serious electromagnetic interference, loss of soft switching characteristics, and low utilization of magnetic components. In response to the above issues, this article proposes an improved hybrid control strategy of combining input control with PFM for optimization. This control strategy is applied to Buck-Boost Quasi-Resonant Converter (QRC), and voltage regulation is achieved through frequency conversion control, which can avoid distortion of the output waveform when the switching frequency changes over a large range, and has strong practicality. The applied converter was designed in Continuous Conduction Mode (CCM) and full-wave mode, and finally simulated under the improved control strategy proposed in this paper, verifying the feasibility of the method.
Through a 66kV coil burning accident of a company for analysis, the use conditions of coil and the real cause of the coil failure, the working principle, the precautions are introduced. And then the causes for arc coil failure are listed. the whole process of the test and judgment of the 66kV arc suppression coil burn accident are expounded. The chromatographic test data and operation report before and after the failure for 66kV arc suppression coil, which proving that 66kV arc suppression coil fault is still due to manufacturing process, and provides scientific basis for analyzing and judging such arc suppression coil faults in the future.
In this paper, the state equation of DC bus voltage is derived by establishing the mathematical model of single-phase PWM rectifier. The results show that DC bus voltage is composed of DC component and double-frequency AC component. In order to suppress the double-frequency of the DC bus voltage, an adaptive state observer without delay is designed. The DC component of the DC bus voltage is extracted by the method of state estimation, so that the DC component and the double-frequency AC component of the DC bus voltage are separated. Only the extracted DC component is introduced into the control loop and the double-frequency voltage ripple is separated from the DC bus voltage control loop. Finally, a simulation model was built in Simulink platform to verify the effectiveness of the proposed method. The simulation results show that the proposed state observer can accurately extract the DC component of the DC bus voltage, eliminate the interference of double-frequency voltage ripple on the control system, and improve the dynamic response ability and stability of the system.
Based on the new demand of national strategic development and the new situation of international competition, the construction of first-class universities and first-class majors and the realization of the higher education connotative development shall be accelerated. In the meantime, new technologies are emerging in the field of electrical engineering, the cross integration of disciplines and specialties is more extensive, and the demand for talents in enterprises become more and more diverse. Therefore, electrical engineering major in our university focus on the goal of National Engineering Education Certification and first-class major construction, proposed “Four-dimensional practical teaching, Multimedia integration, System reconfiguration” multi-innovation methods to conduct major construction.