Omkaresh Byalakere Rudreshaiah

Omkaresh Byalakere Rudreshaiah

Auto-generated profile, based on publicly available information

Omkaresh Byalakere Rudreshaiah

Department of Mechanical Engineering, Siddaganga Institute of Technology, B.H. Road, Tumakuru-572 103, Karnataka, India

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
26 February 2025 in Engineering Research Express
Verified
Journal Article
Closed access
GLGururaj Lalagi
Gururaj Lalagi
PNP B Nagaraj
P B Nagaraj
BOB R Omkaresh
B R Omkaresh
HSHashim Rehman Sharief
Hashim Rehman Sharief
This study uses CFD simulations and experimental methods to investigate the impact of channel geometry and nanofluid concentration on heat transfer performance in microchannel heat exchangers. Results show that increasing nanoparticle concentrations and mass flow rates enhance heat transfer in rectangular and circular channels. At a nanoparticle concentration of 0.05% and a Reynolds number of 500, circular channels demonstrated superior heat transfer performance compared to rectangular channels. Nusselt numbers increased by 18.16% for rectangular and 24.55% for circular channels on average. Pressure drops for both geometries also increased, with a 17.57% rise for rectangular and 16.74% for circular channels relative to the base fluid. Additionally, the pressure drop was 4.72% higher in rectangular channels than in circular ones. Lower Reynolds numbers significantly reduced friction factors, with the minimum friction observed at 0.01% nanofluid concentration. Circular channels exhibited lower friction than rectangular channels across different nanofluid concentrations. CFD and experimental results were in close agreement, particularly regarding pressure drop and temperature, confirming the accuracy of the analysis.

30 November 2019 in Environmental Science and Pollution Research
Verified
Journal Article
Closed access
PDF file
OROmkaresh Byalakere Rudreshaiah
Omkaresh Byalakere Rudreshaiah
YVYatish Kalanakoppal Venkatesh
Yatish Kalanakoppal Venkatesh
SRSuresh Ramappa
Suresh Ramappa

23 November 2025 in Scientia Iranica
Verified
Journal Article
Open access
PDF file
LSLalithamaba H S
Lalithamaba H S
OROmkaresh B. R.
Omkaresh B. R.
ASAisha Siddekha
Aisha Siddekha
AVAnasuya K V
Anasuya K V
Synthesis of magnesium oxide nanoparticles (MgO NPs) using Terminalia chebula seeds extract as fuel by solution combustion method and their applications have been reported in this study. Characterization of the synthesized MgO NPs via Powder XRD, FT-IR, SEM, TEM and EDAX for structural and morphological studies was carried out. MgO NPs were used as a catalyst for production of biodiesel from used cooking oil and for the synthesis of selenoesters. The selenoesters were analyzed by mass spectrometry, 1H NMR, 13C NMR, FTIR techniques and the antifungal activity was investigated for some of the selenoesters against two pathogenic strains F. oxysporum and A. niger with Fluconazole as a standard drug. Biodiesel produced was tested for conformity with the ASTM standard and the results are reported herein. This is one of the novel methods reported for the synthesis of MgO NPs using terminalia chebula seeds, which are easily available, non-toxic, make the NPs green. Catalytic performance of these MgO NPs can be explored further for the synthesis of other organic compounds.

30 December 2023 in Journal of Mines, Metals and Fuels
Verified
Journal Article
Open access
PDF file
BOB. R. Omkaresh
B. R. Omkaresh
RSR. Suresh
R. Suresh
HLH. S. Lalithamba
H. S. Lalithamba
TST. S. Shreyas
T. S. Shreyas
CUC. L. Ujval
C. L. Ujval
SRSrihari
Srihari
Globally biodiesel is one of the best alternative fuels, and is seeing an exponential increase in demand. Despite the bright prospect of biodiesel production, efforts to commercialize it has been very limited. One of the major obstacles has been the high price associated with total production costs. Thus, it is necessary to reduce its processing cost to make biodiesel production feasible. This can be achieved by giving a value-added application for its byproduct. Glycerol is produced as an approximately 10-15% as a byproduct of the transesterification of triglycerides. Glycerol is a valuable byproduct obtained during biodiesel production but it is obtained in a crude form limiting its application. This byproduct needs to be purified efficiently to utilize it. Therefore, the present work aims to report phases in which the crude glycerol is purified. There are two phases in which the crude glycerol is purified. The Crude Glycerol is processed through saponification and then neutralization in the first phase. This produces three layers from which partly purified glycerol is obtained through separation. In the second phase of purification, the glycerol layer is separated from various salt impurities by the use of non-polar solvents. This glycerol is then extracted from the solvent and is subjected to decolorization using charcoal. Soaps and detergents are prepared as a valueadded product from the obtained glycerol.

13 January 2026
Verified
Book Chapter
Closed access
PDF file
SPS. Prashantha
S. Prashantha
BOB.R. Omkaresh
B.R. Omkaresh
BMBasir Maleki
Basir Maleki
Electric vehicles (EVs) and hybrid electric vehicles (HEVs) are a promising solution in promoting carbon neutrality by withstanding climate crisis and providing environmental justice. The challenge is to address the cutting edge of battery technology and battery management systems (BMS,), which lies with the future technologies and breakthrough opportunities in battery materials for advancing electric mobility. The worldwide need for battery materials is growing significantly and is expected to continue for several years. Other factors such as recycling and second use will also affect the demand for materials in BMSs. To address these challenges, materials have evolved as a vital factor in storing electrochemical energy from ultra-capacitors to high specific energy batteries to fuel cells. Over time, battery materials have evolved and dominated the market, starting with lead–acid (mature technology, cheaper), Ni batteries (higher specific energy), lithium batteries (energy density, high specific energy), metal/air batteries (high specific energy, energy density), and flow batteries which are like fuel cells using different materials. The technological aspects of materials need to be explored for high energy storage. Zinc manganese oxide, nanobolt lithium tungsten, gold nanowire, gel electrolyte, organosilicon electrolyte, tank two-string cell batteries, and lithium-sulfur batteries are promising solutions as they are fast charging, affordable, and nontoxic.

22 July 2024 in Journal of Mines, Metals and Fuels
Verified
Journal Article
Open access
PDF file
SPS. Prashantha
S. Prashantha
BOB. R. Omkaresh
B. R. Omkaresh
Friction stir welding is a type of welding that creates friction using a stirring tool while the work-pieces are held together in the welding joint configuration. Friction stir welding is a solid-state welding process. It is one of the efficient ways of joining technology of materials. The friction forces at a microscopic level to change the inner structure of metal properties and it is done by using the kinetic energy of friction in welding methods. This work is majorly carried out to optimize the process parameters like tool rotational speed, Feed, ultimate tensile strength of friction stir welded joint on AA6061 and AA6082 alloy. Welding speed and temperature variation in the workpiece during the welding is recorded for different trials. Failure analysis was carried out for different fractured surfaces by using Scanning Electron Microscope (SEM) revels ductile fracture due to micro void coalescence. The maximum ultimate tensile strength was at a speed of 900 rpm, feed 31.5 mm/min indicates high joint efficiency. Welding speed is more at the feed 90mm/min. Maximum rise in the temperature is at speed 2000 rpm and feed 90 mm/min.