1 May 2001 in IEEE Transactions on Electron Devices
A GaAs solar cell without prismatic covers, with the highest efficiency known to the authors in the range of 1000-2000 suns for a single junction, is presented. Low temperature liquid phase epitaxy is used for its growth. In addition to improvements such as the achievement of a good quality material or a low contact resistance, this solar cell exhibits specific enhanced aspects. Among the most noticeable are: (1) an innovative design; (2) a double and gradual emitter layer; (3) a small size: 1 mm/sup 2/, (4) a finger width of the front metal grid of 3 /spl mu/m; and (5) a tailored ARC deposition based on a nondestructive and accurate AlGaAs window layer characterization. As a consequence, an efficiency of 26.2% at 1000 suns and 25.0% at 2000 suns AM1.5D (standard conditions) is achieved thanks mainly to a short-circuit current density at 1000 suns of 26.8 A/cm/sup 2/ (and 53.6 A/cm/sup 2/ at 2000 suns) with a simultaneous series resistance of 3 m/spl Omega//spl middot/cm/sup 2/.
8 July 2004 in Semiconductor Science and Technology
2 February 2009 in Applied Physics Letters
Photovoltaic conversion efficiencies of 32.6% and 30% at concentrations of 1000 and 3500 suns, respectively, are achieved in monolithic GaInP/GaAs dual-junction solar cells grown lattice matched on a GaAs substrate by metal-organic vapor-phase epitaxy. The tunnel-junction design, based on an (Al)GaAs/GaAs heterojunction, is found to be a key factor for achieving this efficiency at such high concentrations. Moreover, the thorough design and joint optimization of the front grid and the top-cell emitter, using quasi-three-dimensional distributed models, also plays a major role. Efficiencies of over 40% at 1000 suns should be achieved by extending this approach to triple-junction devices.
4 April 2012 in Progress in Photovoltaics: Research and Applications
In this paper, we present a theoretical model based on the detailed balance theory of solar thermophotovoltaic systems comprising multijunction photovoltaic cells, a sunlight concentrator and spectrally selective surfaces. The full system has been defined by means of 2n + 8 variables (beingnthe number of sub‐cells of the multijunction cell). These variables are as follows: the sunlight concentration factor, the absorber cut‐off energy, the emitter‐to‐absorber area ratio, the emitter cut‐off energy, the band‐gap energy(ies) and voltage(s) of the sub‐cells, the reflectivity of the cells' back‐side reflector, the emitter‐to‐cell and cell‐to‐cell view factors and the emitter‐to‐cell area ratio. We have used this model for carrying out a multi‐variable system optimization by means of a multidimensional direct‐search algorithm. This analysis allows to find the set of system variables whose combined effects results in the maximum overall system efficiency. From this analysis, we have seen that multijunction cells are excellent candidates to enhance the system efficiency and the electrical power density. Particularly, multijunction cells report great benefits for systems with a notable presence of optical losses, which are unavoidable in practical systems. Also, we have seen that the use of spectrally selective absorbers, rather than black‐body absorbers, allows to achieve higher system efficiencies for both lower concentration and lower emitter‐to‐absorber area ratio. Finally, we have seen that sun‐to‐electricity conversion efficiencies above 30% and electrical power densities above 50 W/cm2are achievable for this kind of systems. Copyright © 2012 John Wiley & Sons, Ltd.
4 April 2012 in Progress in Photovoltaics: Research and Applications
We present a practical implementation of a solar thermophotovoltaic (TPV) system. The system presented in this paper comprises a sunlight concentrator system, a cylindrical cup‐shaped absorber/emitter (made of tungsten coated with HfO2), and an hexagonal‐shaped water‐cooled TPV generator comprising 24 germanium TPV cells, which is surrounding the cylindrical absorber/emitter. This paper focuses on the development of shingled TPV cell arrays, the characterization of the sunlight concentrator system, the estimation of the temperature achieved by the cylindrical emitters operated under concentrated sunlight, and the evaluation of the full system performance under real outdoor irradiance conditions. From the system characterization, we have measured short‐circuit current densities up to 0.95 A/cm2, electric power densities of 67 mW/cm2, and a global conversion efficiency of about 0.8%. To our knowledge, this is the first overall solar‐to‐electricity efficiency reported for a complete solar thermophotovoltaic system. The very low efficiency is mainly due to the overheating of the cells (up to 120 °C) and to the high optical concentrator losses, which prevent the achievement of the optimum emitter temperature. The loss analysis shows that by improving both aspects, efficiencies above 5% could be achievable in the very short term and efficiencies above 10% could be achieved with further improvements. Copyright © 2012 John Wiley & Sons, Ltd.