Tanjina N. Ahmed

Tanjina N. Ahmed

Auto-generated profile, based on publicly available information

Tanjina N. Ahmed

Materials Science, Engineering, and Commercialization, Texas State University 1 , San Marcos, Texas 78666, USA

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications

1 November 2021 in Journal of Magnetism and Magnetic Materials
Verified
Journal Article
Closed access
LHLauren Henderson
Lauren Henderson
SZSam Zamora
Sam Zamora
TATanjina N. Ahmed
Tanjina N. Ahmed
CBCamila Belduque
Camila Belduque
JTJitendra Tate
Jitendra Tate
WGWilhelmus J. Geerts
Wilhelmus J. Geerts

1 September 2022 in AIP Advances
Verified
Journal Article
Open access
PDF file
TATanjina N. Ahmed
Tanjina N. Ahmed
CBCamila Belduque
Camila Belduque
MCMaggie Y. Chen
Maggie Y. Chen
JTJitendra S. Tate
Jitendra S. Tate
WGWilhelmus J. Geerts
Wilhelmus J. Geerts
Hard-magnetic 3D-printer filaments made of 40 wt. % SrO(Fe2O3)6/PA12 composites made using a twin-screw extruder are being studied to be used for Magnetic Field Assisted Additive Manufacturing (MFAAM). The time dependence of the magnetic properties above the softening temperature of the PA12 matrix but below the melting point was studied using a biaxial Vibrating Sample Magnetometer (VSM). Specifically, the rotation of the magnetic particles in the softened polymer matrix after the application of a rotation field was extracted from the time dependent biaxial VSM signals. Above 132 °C, the strontium ferrite particles can rotate in the nylon matrix. The measured time constant decreases with temperature and magnitude of the rotation field. Model calculations indicate that, for 40 wt. % SrO(Fe2O3)6/PA12 at rotation fields of 500 Oe, the effect of the demagnetizing field on the angle between the magnetic moment and the particle’s easy axis is negligible, allowing one to determine the dynamic “melt” viscosity from the measured transients. The dynamic viscosity decreases from 2 × 105 Pa s at 132 °C to 3.1 × 104 Pa s at 175 °C with a sharp kink observed near 140 °C that correlates with a relaxation from the α′c phase for PA12 observed by others. A yield shear stress was observed for small rotation fields at low temperatures resulting in non-perfect alignment of the magnetic particles. The implications of the measurement results for MFAAM are discussed.

1 February 2023 in AIP Advances
Verified
Journal Article
Open access
PDF file
TATanjina N. Ahmed
Tanjina N. Ahmed
CSChristopher Selsor
Christopher Selsor
JTJitendra S. Tate
Jitendra S. Tate
WGWilhelmus J. Geerts
Wilhelmus J. Geerts
To better understand Magnetic Field Assisted Additive Manufacturing (MFAAM) the effect of a magnetic field on the orientation and distribution of magnetic particles in a molten magnetic composite was studied. Vibrating Sample Magnetometer (VSM) measurements were made on Sr-ferrite/PA12 fused deposition modeling filaments of different packing fraction (5 and 40 wt. %). The rotation of the sample’s magnetic moment upon application of a field perpendicular to the easy axis was monitored with a biaxial VSM above the PA12’s softening temperature. The observed magnetic moment transients depend on the temperature, the applied alignment field, the packing fraction, and the initial field-anneal procedure. Longer field-anneals result in larger time constants and seem to induce a hurdle that prevents complete alignment at low temperatures and/or for small fields. Results indicate the molten composite is a non-Newtonian fluid that can support a yielding stress. Scanning Electron microscopy (SEM) images taken on field-annealed samples at 230 °C show strong chaining with little PA-12 left between individual Sr-ferrite particles suggesting that direct particle to particle interaction is the reason for the observed non-zero yielding stress. The melt viscosity of the composite increases with the number of thermal cycles above the melting temperature (Tm). Room temperature (RT) torque magnetometry measurements show that magnetic anisotropy depends on the field annealing process through induced shape anisotropy contributions originating from magnetic particle agglomerates.