22 April 2020 in IEEE Transactions on Plasma Science
The Chinese Fusion Engineering and Testing Reactor (CFETR) has been performed and is in its engineering design stage. Presently, there are two options allowed for the divertors; the helium-cooled stage and water-cooled stage. The water-cooled one has been focused in this article. The configuration of CFETR divertor module was designed. The cassette design scheme and cassette box inner and outer locking systems were introduced, and the locking system was designed to compliant with the remote-handling (RH) requirements. Two divertor RH design options were provided: one is removed through lower port; the other is targets and baffles removed through upper port; supports and cassette were not removed. The other major research was the water cooling channels' design and its pressure drop calculation. In addition, the fluid, thermal, and mechanical analyses on the outer target were done. Within 10-MW/m2 heat flux, outer target design can ensure that the temperature for all the components works within their temperature limit, and all the components meet the stress design criteria except the copper alloy pipe. The maximum primary stress induced by pressure on the copper alloy pipe appears in the local position between the two monoblocks, which exceeds the design limit. Protection components are need to be added at the gap of the future design optimization to reduce the local stress. After the thermal-hydraulic analysis on water-cooled divertor cassette, the maximum temperature and the maximum stress of cassette meet the requirements. The results of electromagnetic force analysis shows that the deformation on first wall and transition support is less than 0.5 mm, and the maximum stress is also below its tensile strength values. This article summarized the latest achievements in the design and research of CFETR water-cooled diverter in China. All the results will be of great reference for the CFETR divertor optimal design.
1 April 2021 in Fusion Engineering and Design
20 May 2024 in IEEE Transactions on Plasma Science
The Chinese Fusion Engineering Testing Reactor (CFETR) divertor development is ongoing by further optimizing a water-cooled engineering design scheme and implementing the research and development of small-and medium-sized test mock-ups and prototype fabrication. To increase the tritium breeding ratio (TBR), the design scheme adopts a hybrid divertor–blanket integration concept where a breeding blanket is placed underneath targets instead of a cassette. The novel front-face remote handling (RH) targets are designed aiming to explore whether the targets could be maintained from the plasma side. Three unique independent RH design schemes are developed separately for the inner, dome, and outer targets. Hypervaportron flat-tile units are optimized in the high heat flux (HHF) area with an engineering requirement of 20 MW/m $^{2}$ steady-state heat load. All the targets have good RH compatibility with RH tools in the maintenance procedure. Preliminary analysis with respect to pumping performance, hydraulics, heat removal ability, and structure meets the requirements. The research and development is based on advanced fusion reactor materials and realizable materials’ connection technology. The advanced materials of potassium-doped tungsten (KW), oxide dispersion-strengthened copper (ODS-Cu) alloy, and reduced activation ferritic/martensitic (RAFM) steel are used as armor, heat sink, and structural materials, respectively. One of the realizable material connection routes is that RAFM steel is explosively welded with ODS-Cu and then the KW/Cu flat tiles are brazed with ODS-Cu. The small-sized mock-up successfully endured 1000 cycles with 20 MW/m $^{2}$ steady-state heat load. The maximum temperature of the KW surface was 882 $^{\circ}$ C, much lower than the supposed recrystallization temperature. The ultrasonic testing (UT) showed no defects exceeding $\Phi $ 2 mm equivalent before/after the testing. The medium-sized mock-up showed that the UT results meet the requirements and the profile error of the plasma-facing surface is less than 1 mm. All this work will be beneficial for the final engineering design of the CFETR divertor.
16 March 2022 in IEEE Transactions on Plasma Science
The design of the China Fusion Engineering Test Reactor (CFETR) device is one of the main tasks in the next stage of research on fusion energy in China. The CFETR divertor is a key in-vessel plasma-facing component, which will suffer from sputtering erosion and exfoliation caused by intense plasma bombardment, severe heat fluxes, and neutron irradiation. Due to neutron activation of in-vessel components, remote handling (RH) technology has been considered as one of the essential issues of the CFETR divertor. In this article, a new concept of an integral hybrid divertor blanket for the CFETR is proposed, which is feasible for installation and disassembly in CFETR vacuum vessel by RH. Dome is an important part of the CFETR divertor, which comprises 80 modules, and each module is composed of flat-type plasma-facing units (PFUs), steel supports (SSs), and RH compatible structures. Every Dome module is connected to the CFETR blanket by RH compatible structures. This article mainly carries out the conceptual design of Dome (option), degree of freedom (DOF) analysis, stability analysis, RH process planning, and flow field analysis of cooling scheme, which will provide a solid foundation for its subsequent thermal-hydraulic analysis.
1 September 2021 in Fusion Engineering and Design
22 May 2023 in Fusion Science and Technology