8 April 2022 in IEEE Journal of Solid-State Circuits
A broadband three-stage pseudo-differential SiGe-interconnection bipolar transistor (HBT) power amplifier (PA) for high-speed communication at around 300 GHz is presented. The amplifier is fabricated in an experimental 130-nm SiGe BiCMOS technology with an $f_{t}/f_{\max }$ of 470/650 GHz. The use of asymmetric coupled line transformers is proposed to facilitate broadband impedance transformation with device reactance compensation at all amplifier interfaces. The amplifier achieves a maximum small-signal power gain of 23.0 dB and a $P_{\mathrm{ sat}}/{\mathrm{ OP}}_{\mathrm{ 1\,dB}}$ up to 9.7/6.7 dBm, respectively. It shows a 3-dB bandwidth of 63 GHz (239–302 GHz) in small-signal operation and 94 GHz (223–317 GHz) when saturated. The amplifier consumes about 360 mW at a 3-V supply voltage yielding a peak power-added efficiency (PAE) of 1.95% at 260 GHz.
10 October 2018 in Semiconductor Science and Technology
1 June 2006 in Thin Solid Films
15 June 2022 in IEEE Microwave and Wireless Components Letters
A power combined wideband power amplifier (PA) covering the $J$ -band (220–320 GHz) is presented in 130-nm BiCMOS technology. The input power is split by two cascaded 1-to-2 power splitters with amplification stages in-between. The four split signals drive four output stages, which have their outputs combined within a 4-way zero-degree combiner. The splitting and combining networks also incorporate impedance matching. After de-embedding the I/O pads and baluns of 2 dB loss at each side, the PA achieves a gain of 20 dB at the middle of the band and a minimum gain of 17 dB at 320 GHz with I/O return losses below $-$ 5 dB. The PA records a saturated output power ranging from 9.5 to 14.5 dBm across the $J$ -band. It consumes 710 mW from a 3 V supply which corresponds to a drain efficiency ( $\eta_d$ ) of 3.15% at 270 GHz. The presented PA achieves twice better bandwidth with 1.5 times better $\eta_d$ than the state-of-the-art silicon-based amplifiers above 200 GHz. To the authors’ knowledge, this is the first PA covering the whole $J$ -band in silicon technologies.
23 July 2024 in IEEE Transactions on Terahertz Science and Technology
This work focuses on a systematic analysis of the potential as well as the limitations of modern SiGe HBT devices for broadband passive room-temperature detection in the lower THz range. Multiple necessary conditions need to be fulfilled to facilitate broadband passive imaging with a sufficiently low in-band NEP, which refer to various technology-driven device operation aspects, including the rectification process at THz frequencies and low-frequency analysis. Considering a strong frequency dependence of the devices' inherent rectification potential, an in-depth understanding and proper modeling of the device internal parasitics in combination with antenna-detector co-design aspects are crucial for successful detector implementation. For that purpose, a simplified nonlinear high-frequency detector model was applied for the device operating not only in the classical forward-active region but also in deep saturation (cold operation). The complete detector was implemented in a modern high-speed 130 nm SiGe HBT technology with $f_{t}/f_{max}$ of 470/650 GHz. It comprises two independent orthogonal polarization paths within a single dual-polarization lens-coupled on-chip antenna to operate with unpolarized passive illumination. With the aid of an efficient antenna-circuit co-design, a close-to-optimum detector performance in a near-THz fractional bandwidth can be achieved, as experimentally verified in free-space with frequency-tunable coherent CW sources. In particular, the detector optical NEP for each independent polarization path was measured across 200–1000 GHz reporting state-of-the-art values of 2.3–23 pW/ $\mathrm{\sqrt{Hz}}$ and 4.3–45 pW/ $\mathrm{\sqrt{Hz}}$ with the device operating in the forward-active range and in saturation, respectively. This, in combination with the de-embedded equivalent noise bandwidth of 512 GHz centered around 430 GHz, allowed to demonstrate the corresponding 1-Hz defined NETD of 0.86 K and 2 K in a focused measurement setup with a cavity black-body standard chopped mechanically at 1.5 kHz. With a simultaneous dual-channel operation, the NETD scaled down to 0.64 K, indicating near-zero noise correlation between both polarization paths.