In general, a magnetic flux leakage (MFL) pipeline inspection gauge (PIG) has been applied to nondestructive testing for investigating ferromagnetic materials, such as underground gas pipelines. Although MFL PIG is efficient to the inter-city large-scale pipelines, it is hard to apply to small-size pipelines that are usually installed in the city, because the permanent magnet for MFL PIG is too big and heavy to operate inside the small pipe. The strong adhesive magnetic force of permanent magnet to the pipe wall also prevents the usage of MFL PIG in small pipelines. In this paper, we propose a new technology of nondestructive inspection by using a differential coil, which is easy to be manufactured with lightweight, low cost, and simple structure for operating inside the underground pipelines. Comparing with the conventional permanent-magnet MFL PIG, the results of the proposed system could also maximize the detection sensitivity of defect signals and minimize the magnetic adhesive force on the pipe wall simultaneously.
The magnetic flux leakage-type nondestructive testing has been applied for the highly efficient inspection of defects in ferromagnetic materials such as underground gas pipelines. In the system, the magnetic field is applied to magnetize a steel pipe so as to induce the leakage signal in the vicinity of defects on the pipe. From the measured sensor signals, decomposing or estimating sizes and shapes of defects are necessary. For the maintenance, the depth estimation is the most important procedure for the management of a safety accident. However, the previous depth estimation contains high error rate inevitably because the depth signal implies the width and length error simultaneously. This paper focused on the enhanced algorithm for the depth sizing in various defects by using the decoupling algorithm to enhance the accuracy of defect depth. Estimated results show good agreements with measured ones.
This paper presents the design of cryogenic induction motor submerged in liquefied natural gas (LNG) for operating LNG spray pump. In cryogenic environment of -163 °C, the torque characteristics of induction motor differ greatly from the operating conditions at room temperature. So, in order to obtain the operating characteristics corresponded with design specifications of the induction motor in cryogenic environment, it is necessary to redesign motor dimensions from the result of conventional design by reflecting the changes of material properties under the very low temperature (VLT). This paper focused on the design of cryogenic induction motor considering the variation of resistivity for the stator windings and rotor bars. Also, the distribution of magnetic flux density and magnetic saturation effect on the steel core are analyzed by using 2-D finite-element method for ac sinusoidal time varying excitations under the VLT. The result of proposed method considered the magnetic and electric characteristics of matters in VLT successfully, so that the motor performances at the cryogenic temperature fit well with expected. The designed motor was fabricated and torque performance measured in VLT agreed well with design goals.
13 August 2021 in IEEE Transactions on Plasma Science
Since 2016, Hanwha Defense Corporation has been working on applying electromagnetic launch technologies such as induction coilguns to cold-launch systems that can launch guided missiles. First, a design procedure of a multistage coilgun system based on the pulsed power driven by capacitor banks was developed using the Taguchi method, and a laboratory-scale three-stage coilgun capable of launching a 21.68-kg projectile at a maximum speed of 27.5 m/s was built and the results of the experiment were announced in 2018. In this article, we design, fabricate, and present the experimental results of a pulsed power-based four-stage induction coilgun using the proposed procedure to prove the validity of the electromagnetic launch technology for heavy missile launch. In this experiment, a 100-kg projectile was fired under 4-kV charging conditions, the maximum speed of the projectile was 25 m/s or more, and an efficiency of 15% was achieved without considering the mass of the armature. In this study, by accelerating a 100-kg projectile to 27 m/s, the feasibility of an electromagnetic launcher developed for heavy missile launch was verified.
The magnetic flux leakage (MFL) type pipeline inspection gauge (PIG) is commonly used to detect defects on the underground pipelines as one of the nondestructive testing instruments. Although it is effective for the inter-city scale large size pipeline, it is hard to detect defects for the small size pipeline installed inside the city. So, it is necessary to adopt self-driving robot system to drive PIG module because the small gas pressure inside a small size pipeline is not enough to push PIG module. Even though it is enough to pass in straight line, when this module passes through bent pipe or welded pipe joint, the magnetic force between pipe and inspection module is increased sharply so that the PIG module could be stuck eventually. This paper proposed a new design structure of MFL system to decrease stuck forces on the pipe wall. All structural parameters for MFL sensors based on the magnetic field theory were designed to minimize the magnetic force and maximize the detection sensitivity of defect signals. The performance of the proposed system was verified by simulation results using 3-D finite-element method and experimental measured ones.
1 January 2019 in IEEE Transactions on Plasma Science