Xinxin Zhu

Xinxin Zhu

Auto-generated profile, based on publicly available information

Xinxin Zhu

University of Science and Technology of China, Hefei, China

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
19 September 2023 in IEEE Transactions on Applied Superconductivity
Verified
Journal Article
Closed access
HLHui Lu
Hui Lu
YHYanlan Hu
Yanlan Hu
YXYezheng Xiao
Yezheng Xiao
XLXiaofei Li
Xiaofei Li
LZLonggui Zheng
Longgui Zheng
XZXinxin Zhu
Xinxin Zhu
High-Temperature Superconducting (HTS) Current Leads (CL) made of Bi-2223 superconducting tapes in Experimental and Advanced Superconducting Tokamak (EAST) are connected with the superconducting magnets and power supplies. The quench detection systems consist of primary (resistive voltage-based) and backup (temperature-based) detection systems; due to the required fast response time, the quench detection system for the EAST HTSCL relies primarily on direct voltage measurement. The traditional temperature and voltage detection methods have two main defects. Firstly, to prevent the temperature sensor from high-voltage breakdown, it has to be installed in the rear section of the insulators, leading to its sensitivity decreasing significantly. Secondly, because the average zone propagation velocity of HTS is around 1/100∼1/1000 of Low-Temperature Superconducting (LTS) materials, the small resistive voltage during quench is very difficult to detect. Distributed Optical Fibers Quench Detection (DOFQD) based on Raleigh Scattering (RS) can be a solution, which adopts the special communication glass fiber as the sensor. It can continuously monitor temperature changes (0.5 K to 2 K) at intervals of 5 mm. At the same time, the method has the advantages of high-voltage resistance and immunity from electromagnetic interference. But the biggest drawback of this method is that the Optical Fiber (OF) sensor is very brittle in the transverse direction resulting in complicated installation. Recently, the OF sensor has been directly laid inside the insulation layer of the HTSCL and led out of the vessel successfully. Meanwhile, the Parsons discharge test, the thermal shock test, and the vacuum leakage rate test can come up with the technical requirements. The power-on test was shown that DOFQD could detect a quench ahead of voltage measurement when the HTSCL was soaked in the 77 K liquid nitrogen. The next plan is to apply this quench detection method in the EAST HTSCL.

10 September 2025 in IEEE Transactions on Applied Superconductivity
Verified
Journal Article
Closed access
YCYu Chen
Yu Chen
YHYanlan Hu
Yanlan Hu
YXYezheng Xiao
Yezheng Xiao
QYQing Yan
Qing Yan
LZLonggui Zheng
Longgui Zheng
QNQicai Ni
Qicai Ni
In the next generation of fusion devices, the central solenoid (CS) coil needs to withstand large alternating currents and rapidly changing magnetic fields to achieve plasma breakdown, configuration formation and control. In this study, the quench behavior of a representative submodule (CS1U-LTS) is investigated under time-varying current and magnetic field conditions, where the local field ramp rate reaches approximately 2.5 T/s. This alternating operation mode significantly affects the stability of superconducting magnets. However, the current simulation of superconducting magnet quench is mostly based on steady-state current and steady-state background field, which is difficult to reflect the quench propagation characteristics of superconductors under alternating conditions as the current and magnetic field intensity and direction change. To ensure the safe operation of the CS coils under alternating conditions, this paper first analyzes the quench behavior in a reference case with constant peak current prior to an exponential discharge and determines the protection thresholds required to limit the hot spot temperature to below 150 K: 200 mV voltage threshold and 0.5 s time threshold. The quench response at the positive and negative current peaks during time-varying operation is further analyzed. The results show that under the same protection conditions, the maximum temperature of the CS1U-LTS coil in alternating operation still meets the design requirements. In addition, this paper compares the differences in quench propagation near the two peak points, revealing the impact of alternating operation on quench propagation behavior.

29 August 2025 in IEEE Transactions on Instrumentation and Measurement
Verified
Journal Article
Closed access
QYQing Yan
Qing Yan
YXYezheng Xiao
Yezheng Xiao
QNQicai Ni
Qicai Ni
LZLonggui Zheng
Longgui Zheng
TWTeng Wang
Teng Wang
YHYanlan Hu
Yanlan Hu
Induced voltage noise is a significant source of interference in voltage detection, seriously affecting measurement accuracy and system stability. In the complex electromagnetic environment of the Tokamak system, induced voltage noise can exceed 500 V, posing a great challenge to noise suppression in voltage detection signals. This paper presents a two-stage noise compensation approach designed to address the problem. The first stage utilizes a hardware-based Co-wound Wire (CWW) primary compensation method, effectively reducing the induced voltage noise from over 500 V to below 10 V. Building on this foundation, the second stage introduces a deep learning model based on CNN-BiLSTM-Attention as the secondary compensation module, which further reduce the residual noise to below 100 mV over a 1-second window. The proposed method was validated through real-time deployment on the Experimental Advanced Superconducting Tokamak (EAST). Experimental results demonstrate that the method not only achieves excellent compensation effect but also preserves the integrity of critical voltage detection signals throughout operation.

16 September 2025 in IEEE Transactions on Applied Superconductivity
Verified
Journal Article
Closed access
XZXinxin Zhu
Xinxin Zhu
YXYezheng Xiao
Yezheng Xiao
YHYanlan Hu
Yanlan Hu
LZLonggui Zheng
Longgui Zheng
QYQin Yan
Qin Yan
QNQicai Ni
Qicai Ni
The quench detection system for next-generation fusion device of China face enormous challenges, as their magnet systems are characterized by significantly higher stored energy and faster discharge rates than those in predecessors like EAST and KSTAR. During both the plasma discharge phase and the superconducting magnet quench current discharge phase, rapid current changes induce high and dynamically varying voltages on magnets, particularly in the Central Solenoid (CS) and Poloidal Field (PF) coils, where kilovolt-level inductive voltages can arise. These high-voltage signals can appear on the quench detection signal cables connected to the magnets, leading to capacitive coupling crosstalk between these cables within the same cable tray. Such crosstalk severely interferes with the quench detection signals, compromising the accurate identification of magnet quenches. This can potentially lead to either false quench detection or a failure in quench detection. To address this, the paper presents a systematic investigation into the crosstalk phenomenon. It begins by characterizing the properties of quench detection signals. Subsequently, an electrical circuit model for signal cable crosstalk is established, and the influencing factors of crosstalk are analyzed. Finally, the model is validated through a dedicated experiment, whose results are used to predict crosstalk levels in the operational environment and to propose effective mitigation strategies to ensure robust quench detection.

16 August 2022 in IEEE Transactions on Applied Superconductivity
Verified
Journal Article
Closed access
XZXinxin Zhu
Xinxin Zhu
YHYanlan Hu
Yanlan Hu
TWTeng Wang
Teng Wang
YSYi Shi
Yi Shi
YXYezheng Xiao
Yezheng Xiao
A superconducting electric transformer (SET) is a key element in the conductor performance test platform of the Comprehensive Research Facility for Fusion Technology, which has the capacity to provide around 100-kA test current for superconductor testing. Quench detectors based on voltage measurement is the considered solution for the quench detection in the primary windings (PWs) of the SET. One of the major problems to be encountered during the operation of the primary magnet systems is the expected inductive, coupled signals due to the current ramp up/down. For this case, Wheatstone bridge compensation can work. Regarding the hotspot temperature restriction, the quench detection threshold value and the holding time are given based on quench simulation results. Because the inductance of the PW is huge, the choice of dumping resistance plays a key role to ensure that the stored energy should be released safely if quench events occurred.

2 April 2026 in IEEE Transactions on Applied Superconductivity
Verified
Journal Article
Closed access
XZXianzhou Zhao
Xianzhou Zhao
YHYanlan Hu
Yanlan Hu
JJJincheng Jiang
Jincheng Jiang
YCYu Chen
Yu Chen
QYQing Yan
Qing Yan
LHLiangbing Hu
Liangbing Hu
The China Fusion Engineering Test Reactor Central Solenoid Model Coil (CSMC) project, which commenced construction in 2014, is currently in the experimental phase. Experimental advanced superconducting tokamak (EAST) is a superconducting tokamak nuclear fusion experimental device located in China, dedicated to researching the controllable technology of nuclear fusion and currently in continuous operation. The quench protection system serves as the primary safeguard for the operation of the magnets and plays a critical role in ensuring the success of operational experiments. A key component of this system is the voltage acquisition detection lines, which continuously monitor the magnet’s operational status. The safe and reliable operation of these detection lines is essential for the precise functioning of the system. However, the high-voltage detection lines are subjected to harsh environmental conditions, including nuclear radiation, high voltages, ultra-low temperatures, and other extreme factors. Over time, these cables are prone to electrical failures, such as disconnections, short circuits, and insulation damage. This article applies broadband impedance testing [frequency domain reflectometry (FDR)], a mature nondestructive testing technology, to accurately and rapidly detect and locate various electrical faults in the quench detection lines of CSMC and EAST. Real-world field test results for CSMC and EAST verify that FDR can achieve high-precision fault location for twisted-pair and four-core cables, and effectively distinguish typical faults, such as short circuits, open circuits, and water ingress. The application of FDR provides a reliable technical means for the maintenance and safe operation of quench detection systems in superconducting magnet devices, and can prevent latent defects from evolving into permanent faults.