The present works deals with the implications of non-uniform anode particle morphology on charging and discharging characteristics of Lithium-ion cell, especially for ultra-fast charging applications. The one-dimensional isothermal model is employed to analyze the effect of C-rate, porosity, tortuosity, and particle geometry for a range of non-uniform anode particle size distribution numerically. Our study reports that the value of capacity and specific power of the cell is found to be maximum when the particle size decreases along the electrode length. In contrast, capacity and specific power are minimum when anode particle size increase along the anode length. Moreover, a significant improvement in the performance of the Lithium-ion battery is found at ultra-fast charging when non-uniform particle distribution is employed. Additionally, a strong interplay of particle distribution and microstructural attributes viz. porosity and tortuosity on cell performance are revealed for the charging-discharging cycle. Further, the capacity of the cell is found to be maximum when the particle geometry is spherical. We anticipate that the results can inspire further improvement in ionic transport for ultrafast charging with non-uniform microstructure in the Li-ion cell.
22 December 2023 in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
Microchannel research has emerged significantly in the last decade due to its several applications, viz., heat exchanger, pharmaceutical, etc. Although several micro-machining processes have been developed in the previous few decades, the contemporary utilization of laser micromachining is minimal. In this context, the current research investigates the material characterization and thermal analysis of corrugated aluminum channels using an experimental and numerical approach. Herein, the types of equipment used are pulsed laser, scanning electron microscope, and energy-dispersive X-ray spectroscopy for experimental analysis. Moreover, the numerical investigation has been conducted using the finite-element method. The current study developed a numerical model for transient thermal analysis utilizing a Gaussian heat source. After that, the output data value is comparable to laser micromachining for experimental inquiry. The results of laser micromachining are shown in terms of heat affected zone (HAZ), depth, and width. The microstructural analysis revealed that the coarser grains are formed near HAZ, whereas finer grains with cracks are located near the laser focal point.
31 May 2023 in Iranian Journal of Science and Technology, Transactions of Mechanical Engineering
In the present paper, plasma-assisted physical vapor depositions (PAPVDs) have been used to extract the TiN and titanium aluminum nitride (TiAlN). Further, plasma nitriding (PN) has been used prior to thin-film deposition of TiN on AISI 304 stainless steel material using intentional biasing (in the coating). PAPVD is integrated to investigate the thermal resistant effect coating of AISI 304 stainless steel by TiN coating using finite-element analysis. The morphology of elements on the coating was studied by field emission scanning electron microscopy, X-ray diffraction (XRD), and energy-dispersive X-ray spectroscopy. From XRD analysis, it has been observed that at the coated zone Ti, TiN was found on the AISI 3O4 stainless steel. The results in microhardness through the Vickers microhardness tester have been measured up to 350 Hv for the base sample at a 10 g load. Moreover, TiN/(PN + TiN) coated samples were measured with an average microhardness of 2220, 963, and 720 Hv for the nitride sample. In addition to this, the microhardness of TiAlN was found up to 1890 and 2400 Hv for different samples. The thickness of the film is around 1.4279 µm (TiN) and 1.888 µm (TiAlN) in 1 h of deposition.
21 April 2020 in Journal of Electrochemical Energy Conversion and Storage
The present study numerically investigates the implication of different porosity configurations, viz., uniform, algebraic, trigonometric, logarithmic, and stepwise constant porosities at the negative electrode on performance characteristics of Lithium-ion cell. We assess the merit of nonuniform porosity over uniform one in terms of cell performance characteristics, viz., specific energy, capacity, electrolyte salt concentration, local volumetric current density, power dissipation density, and solid lithium concentration. Our results reveal that specific energy and capacity are found to be maximum when the porosity increases logarithmically in the direction from the negative electrode–current collector to negative electrode–separator interface. Also, it is found that the variation of power dissipation density and electrolyte salt concentration characteristics are dictated by the interplay of the porosity and the length of the negative electrode. Furthermore, the effect of charging rates (quick charge, fast charge, and ultrafast charge) on cell performance is carried out. It is seen that the increment in C-rates strongly influences the cell performance. It is found that the average capacity increases by 44% at the higher C-rate, i.e., 5C when the porosity increases logarithmically. On the contrary, sinusoidal variation in porosity yields in the worst cell performance. The findings of the present study bear utility toward designing an efficient battery system that can operate for a higher number of cycles with minimal power dissipation density and can fit into the ultrafast charging technique.