15 June 2017 in Eastern-European Journal of Enterprise Technologies
We developed a procedure for the optimization of thermal modes and parameters of the cooling system of induction traction engines of tram carriages. The procedure includes the following basic steps. The optimization of operating modes of an induction traction drive by the criterion of effectiveness of its work under different modes. The optimization of motion modes of a tram carriage along a track section with the assigned motion schedule and profile based on the curves of the motion of a tram carriage, optimal by the criterion of energy consumption, using the method of Hamilton-Jacobi-Bellman. The optimization of parameters of the cooling fan of traction engines by the criterion of efficiency of a cooling system using the Weyl method by the generalized golden section. It is proposed to conduct determining of operating modes of a traction drive in advance based on the solution to the problem of conditional optimization of its modes. In order to determine the optimal operating modes of a traction drive, we selected a combined method: global search is executed by genetic algorithm with a one-point crossover and by selection on the principle of roulette. At the final stage of an optimization procedure, optimum refining is carried out using the Nelder–Mead method. When a tram carriage moved along a track section, we defined the following. We determined the optimal modes of motion of the tram carriage T-3 VPA with induction traction engines for a track section with the assigned motion schedule. It was found that, compared with the basic design, efficiency of the cooling system increased by 27.6 %, which corresponds to a reduction in the proposed criterion of efficiency. Based on the results of modeling a traction engine with an optimal fan, it was established that the largest overheating is observed in the frontal part of the stator winding. The temperature is 139.6 °C at second 3363 from starting the motion and it does not exceed a permissible value of 140 °C.
4 April 2018 in Eastern-European Journal of Enterprise Technologies
We have studied a traction drive based on the synchronous motor with excitation from permanent magnets for its electrical losses. A simulation model of the traction drive is synthesized, which employs the algorithm of a space-vector PWM. A special feature of the model is the application of parameters of actual IGBT-transistors and the possibility for obtaining instantaneous values of electric losses in transistors and snubbers of the inverter under different modes of operation. We have devised a procedure for calculating electric losses in the traction engine based on the shape of phase currents, geometrical and electrical parameters of the engine. Simulation of the traction drive and calculation of losses in the traction engine is integrated, which makes it possible to account for the impact of the inverter and engine on each other.We have simulated work of the reducer-free traction drive based on a synchronous motor with excitation from permanent magnets with a capacity of 80 kW. The dependences were constructed for losses in the traction inverter and engine on the clock frequency of a space-vector PWM and motion speed.The proposed procedure makes it possible to quantify the magnitude of electric losses in the traction drive elements depending on the types of transistors applied, clock frequency of the inverter, and parameters of the engine. This enables the optimization of the traction drive for the criterion of maximum performance efficiency, as well as thermal calculation of the elements of the drive.
10 April 2021 in Electrical Engineering & Electromechanics
Goal. The goal of the research is to develop an algorithm for selecting the main dimensions of a traction permanent magnet-assisted synchronous reluctance motor. Methodology. A method for determining the main dimensions of the motor, which combines the analytical selection of stator parameters and numerical field calculations for the selection of rotor parameters. The need to check the mechanical strength of a rotor with permanent NdFeB magnets in flux barriers is shown. Results. The article proposes an algorithm for selecting the main dimensions of a traction permanent magnet-assisted synchronous reluctance motor, which combines analytical expressions for selecting stator parameters and numerical field calculations for selecting rotor parameters. It is determined that analytical methods for calculating the magnetic circuit need to be developed in order to reduce the time to select the main dimensions of the motor. Originality. For the first time the sizes of active parts of the permanent magnet-assisted synchronous reluctance motor with power of 180 kW for the drive of wheels of the trolleybus are defined. Practical significance. As a result of research the sizes of active parts, stator winding data and a design of a rotor of the electric motor are defined. The obtained results can be applied when creating an electric motor for a trolleybus.
29 June 2023 in Reporter of the Priazovskyi State Technical University. Section: Technical sciences
The issue of updating the locomotive fleet of industrial enterprises by modernizing outdated diesel locomotives with hydraulic power transmission was considered. The analysis of existing modernizations shows the possibility of using traction electric drive while preserving the original group drive of wheel pairs. This approach is used by manufacturers when updating outdated and creating new diesel locomotives and traction modules for rolling stock. A possible option is the use of single-motor carts. Previous studies on the choice of the type of wheel pairs drive were analyzed and it was established that the use of a group drive of wheel pairs provides the possibility of realizing high traction forces without additional devices, and the drive itself has a lower cost. This determines the expediency of using a group drive of wheel pairs when modernizing diesel locomotives with hydraulic power transmission. To realize these advantages, it is necessary to use a traction electric drive based on electromechanical alternating current converters. This approach was implemented by Mykolaiv Locomotive Repair Plant LLC during the modernization of TGM6 diesel locomotives. The diesel locomotive is intended for shunting and hauling operations, as a result of which it was assumed during the design that the traction force when moving is equal to 320 kN, the continuous traction force is 300 kN, and the maximum speed is 50 km/h. The power plant consists of a modern Cummins diesel engine and a synchronous generator. A frequency-controlled asynchronous traction electric motor is used to drive the wheel pairs. Power and control of the electric motor is carried out using a voltage inverter. Diesel locomotives use a controlled electric drive of cooling motor-fans, and semiconductor converters are used to power auxiliary systems. The locomotive and its systems are controlled by a microprocessor control system. The application of the traction electric drive based on the asynchronous electric motor provided the estimated efficiency of the diesel locomotive and the efficiency of the diesel power at the nominal power and the estimated speed of the long-term mode, equal to 6 km/h, are 0.312 relative units and 0.69 relative units, respectively. The analysis of ways to improve the traction electric drive to reduce the consumption of fuel and energy resources was carried out. It was determined that the use of a power plant with energy storage and the use of two traction electric motors for the group drive of wheel pairs may be expedient
27 April 2016 in Eastern-European Journal of Enterprise Technologies
The actual problem of creating a high-speed railway rolling stock with a combined electromechanical and pneumatic body tilt system is considered. Using the proposed simulation model created in the MATLAB environment, simulation of the rolling stock body tilt while passing a curved track section is carried out. To determine the parameters of the elements of electromechanical and pneumatic drive units, information is necessary about the electrophysical processes, occurring in the tilt system and determining the input parameters for the design of the considered tilt system. The dynamic performance of components of the proposed mechanism is identified, which allows giving practical advice on the choice of parameters of semiconductor converter elements, pneumatic and electromechanical devices of the combined tilt system, and also determining the forces acting in the tilt mechanism elements. Based on these dependencies, it is possible to choose the element base of the semiconductor converter (types of keys and diodes), parameters and types of cylinders of air springs, as well as to determine the load of the elements of the overbogie structure of the rolling stock. The results can be used in the development and design of high-speed railway rolling stock without substantial reconstruction of the existing transport infrastructure.
31 October 2018 in Eastern-European Journal of Enterprise Technologies
Determination of optimal parameters of the pulse width modulation of the 4qs transducer for electriс rolling stock