24 August 2020 in Journal of Fluid Mechanics
It is well known that perforation of a flat plate reduces its drag when exposed to a flow. However, studies have shown an opposite effect in the case of cylinders. Such a counterintuitive result can have significant consequences on the momentum modelling often used for wind turbine performance predictions, where increased porosity is intrinsically linked to lower drag. Here, a study of the drag of various types of porous cylinders, bars and plates under steady laminar inflow is presented. It is shown that, for most cases, the drag decreases with increased porosity. Only special types of perforations can increase the drag on both cylinders and bars, either by enhancing the effect of the rear half of the models or by organizing the wake structures. These rare occurrences are not relevant to wind turbine modelling, which indicates that current momentum models exhibit the qualitatively correct behaviour.
12 January 2023 in Journal of Fluid Mechanics
In this article, we present an entrainment-based model for predicting the flow and power output of finite-length wind farms. The model is an extension of the three-layer approach of Luzzatto-Fegiz & Caulfield (Phys. Rev. Fluids, vol. 3, 2018, 093802) for wind farms of infinite length, and assumes dependence of key flow quantities, such as the wind farm bulk velocity, on the streamwise distance from the farm entrance. To assist our analysis and validate the proposed model, we undertake a series of large-eddy simulations with different turbine spacing arrangements and layouts. Comparisons are also made with the top-down model with entrance effects of Meneveau (J. Turbul., vol. 13, 2012, N7) and data from the literature. The finite-length entrainment model is shown to be capable of capturing the power drop between contiguous rows of turbines as well as describing the advection and turbulent transport of kinetic energy in both the entrance and fully developed regions. The fully developed regime is approximated only deep in the wind farm, after approximately 15 rows of turbines. Our data suggest that for the cases considered in this study, the empirical coefficients that can be used to describe turbulent entrainment and transfers above the wind farm exhibit little dependence on the farm layout and may be considered constant for modelling purposes. However, the flow field within the wind farm layer can be strongly modulated by the turbine density (spacing) as well as the array layout, and to that extent it can be argued that they are both primary factors determining the wind farm power output.
17 August 2020 in Journal of Fluid Mechanics
During its collapse a bubble can draw and concentrate energy from its surroundings. In the present work, we investigate the behaviour of certain multibubble configurations that have the potential for achieving significant levels of energy focusing. The dynamics of these configurations are studied for the first time in three dimensions, and are shown to be significantly different from those in two dimensions. Novel observations regarding focusing regimes in collapsing arrays are presented. Finally, through a series of numerical experiments on previously unexplored arrangements, we demonstrate that substantially enhanced levels of energy concentration can be achieved.
31 March 2022 in Physical Review Fluids
Analytical wind turbine wake models are an integral component of wind farm design and optimization. However, when the turbine induction factor increases, these models are prone to failure, as they do not account for the increasingly important effects of low wake pressure. To resolve this issue, this paper proposes an analytical wake model which incorporates the effect of wake pressure in its predictions. The model is based on inviscid flow theory for the initial wake region [K. Steiros and M. Hultmark. J. Fluid Mech. 853, R3 (2018)] and an extension of Morton's [B. R. Morton. J. Fluid Mech. 10, 101 (1961)] theory for the far wake, both of which include the effects of wake pressure. Comparison with high-fidelity wind turbine simulations shows that the model is comparable to conventional ones at low induction factors, but continues to be accurate at higher induction factors where existing models break down.
12 April 2024 in Wind Energy Science
Maximising the power production of large wind farms is key to the transition towards net zero. The overarching goal of this paper is to propose a computational method to maximise the power production of wind farms with two practical design strategies. First, we propose a gradient-free method to optimise the wind farm power production with high-fidelity surrogate models based on large-eddy simulations and a Bayesian framework. Second, we apply the proposed method to maximise wind farm power production by both micro-siting (layout optimisation) and wake steering (yaw angle optimisation). Third, we compare the optimisation results with the optimisation achieved with low-fidelity wake models. Finally, we propose a simple multi-fidelity strategy by combining the inexpensive wake models with the high-fidelity framework. The proposed gradient-free method can effectively maximise wind farm power production. Performance improvements relative to wake-model optimisation strategies can be attained, particularly in scenarios of increased flow complexity, such as in the wake steering problem, in which some of the assumptions in the simplified flow models become less accurate. The optimisation with high-fidelity methods takes into account nonlinear and unsteady fluid mechanical phenomena, which are leveraged by the proposed framework to increase the farm output. This paper opens up opportunities for wind farm optimisation with high-fidelity methods and without adjoint solvers.
20 September 2022 in Journal of Fluid Mechanics
A significant challenge in the experimental or computational characterisation of porous bodies and wind turbines is the correction of the obtained flow quantities for wall interference effects. Conventional corrective models are based on the Rankine–Froude theory, which is valid when the body solidity, or turbine induction factor, is sufficiently low. To resolve this issue, this work presents a new corrective model that builds on an extension of the Rankine–Froude theory, valid at arbitrary solidities, coupled with the method of mirror images to account for the existence of channel walls. The predictions of the new model are validated using laboratory and numerical experiments of porous plates and wind turbines. The results show that the new model performs equally as well as conventional ones when the solidity is low, but becomes increasingly more accurate as the latter grows.